Home Network Community > Wi-Fi Routers > Route configuration Archer C6
< Wi-Fi Routers

Route configuration Archer C6

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Route configuration Archer C6

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Route configuration Archer C6
Route configuration Archer C6
2019-03-21 11:30:47 - last edited 2021-09-10 06:57:20
Model: Archer C1200  
Hardware Version:
Firmware Version:

Hello,
I have the following setup :
                                          +======+
                                          | Internet |
                                          +======+ 
                                                 |||
+======+                          +======+
| Internet |                           |   ISP 2  |
+======+                          +======+
       |||                                   |           | Bridge mode
+======+                          +========+
|   ISP  1 | DHCP                 | TP LINK  |
+======+                          +========+
     | 192.168.42.253                     | 192.168.42.254
     | 192.168.7.254                       |
     | 192.168.8.254                       |
+=========================+
|                      Switch                      |
+=========================+

I configured my network (my router of my ISP 1) to redirect VLAN 7 to the ISP 2 through the TP Link Router.
With the TP WR841N, all was working fine. VLAN 7 and VLAN 42 were routed to ISP 2 and had access to the Internet. Vlan 8 routed to ISP 1.

I bought an Archer C6 to have more Gigabit interfaces and I did the same configuration that I did for the TP WR841N, same IP address, same static route, disable wireless interface, I even take the same Mac address for the Wan interface to not mess with my ISP 2 configuration router (configured in bridge mode). My VLAN 42 still access to the Internet, but my VLAN 7 don't have access to the Internet, but it can access to the TP Link router.

 

Is there any minor/major change between the "TP WR841N" and the "TP Archer C6" that could explain this problem?

 

On the Advanced Routing configuration, I can see that on the TP WR841N, the default gateway (0.0.0.0) is at the end of the routing table (in the web interface), while on the TP Archer C6, the default gateway is at the beginning... but I cannot change the order.

 

Regards

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Route configuration Archer C6-Solution
2019-03-22 08:45:20 - last edited 2021-09-10 06:57:20

I think your 841n is quite an old device, maybe you can check the hardware version.

 

As for as I know, router for home use has restrict the forward rules to its own lan only, for the consideration of security.

Thus as you can see vlan 42 could access internet without any problems, while vlan 7 fails.

 

For the old routers, it has not take so care of security, it is more like router work well is ok.

So you can see, are lan data can be forwarded.

 

In this scenario, you shall choose a business router, for example, TP-LINK load balance router R470T+

It support dual WAN, as you have two ISP lines. It support policy routing, as you can direct vlan42 and vlan7 go via ISP2. It support multi-nets NAT, as you can forward multiply lan data.

Recommended Solution
  0  
  0  
#2
Options
10 Reply
Re:Route configuration Archer C6-Solution
2019-03-22 08:45:20 - last edited 2021-09-10 06:57:20

I think your 841n is quite an old device, maybe you can check the hardware version.

 

As for as I know, router for home use has restrict the forward rules to its own lan only, for the consideration of security.

Thus as you can see vlan 42 could access internet without any problems, while vlan 7 fails.

 

For the old routers, it has not take so care of security, it is more like router work well is ok.

So you can see, are lan data can be forwarded.

 

In this scenario, you shall choose a business router, for example, TP-LINK load balance router R470T+

It support dual WAN, as you have two ISP lines. It support policy routing, as you can direct vlan42 and vlan7 go via ISP2. It support multi-nets NAT, as you can forward multiply lan data.

Recommended Solution
  0  
  0  
#2
Options
Re:Re:Route configuration Archer C6
2019-03-22 16:56:49

Ok, @May thank you for your answer

I think the TL-ER6020 should be more accurate to have Gigabit interface, dual WAN, policy routing and multi-nets NAT.

 

  0  
  0  
#3
Options
Re:Route configuration Archer C6
2021-09-09 12:45:49 - last edited 2021-09-09 12:46:57

@May  I've just bought Archer C6 to replace my old Archer C2, made the same advanced routing configuration and it doesn't work too. I really cannot have two subnets with access to the Internet (WAN) with C6?

  0  
  0  
#4
Options
Re:Route configuration Archer C6
2021-09-10 07:16:24

@PKP 

 

Are you using the same network topology as Akeneo's? You can describe yours in detail, and provide the static routing settings on your C6, we will confirm.

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#5
Options
Re:Route configuration Archer C6
2021-09-10 10:19:04

@Kevin_Z 
My topology is very simple:

Internet
     |
     | 
 WAN
 -----------------
 |  TP-LINK   |
 -----------------
 LAN 192.168.1.1
    |
    |  192.168.1.0/24

    |

 LAN 192.168.1.2
 -----------------
 |  router 2     |
 -----------------

 LAN 192.168.2.1
    |
    |  192.168.2.0/24

    |

    ....

TPLINK has a static route to destination 192.168.2.0 set to IP GW 192.168.1.2
Ping from 192.168.1.* to 192.168.2.* works.
Ping from 192.168.2.* to 192.168.1.* works.
Ping from 192.168.1.* to internet works.
Ping from 192.168.2.* to internet works with TP Link Archer C2, but not with Archer C6. Same configuration.

  0  
  0  
#6
Options
Re:Route configuration Archer C6
2021-09-10 16:34:58

@PKP 

 

What's the make and model of Router 2 and what is its purpose ?

To which router your client devices are connected ?

Is it feasible to set the router 2  in AP mode so you'll avoid the double NAT in your network ?

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#7
Options
Re:Route configuration Archer C6
2021-09-10 19:56:21 - last edited 2021-09-10 19:58:43

@terziyski 

Router 2 is AirGrid M5 HP, its purpose is to split local network into another subnet, which has its own broadcast services (local computers, printers) and users.

There is no double NAT, router 2 simply routes between two subnets. The only NAT is on TP-LINK to WAN interface.

The main fact is the TP-LINK Archer C2 works, C6 doesn't, it blocks traffic from different local subnet to WAN :-(

  0  
  0  
#8
Options
Re:Route configuration Archer C6
2021-09-11 08:34:32

@PKP 

 

Are you sure about the router 2 ? AirGrid M5 HP is an Ubiquiti wireless access point CPE.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#9
Options
Re:Route configuration Archer C6
2021-09-11 14:58:52

@terziyski Sure, Ubiquiti configured in SOHO Router Mode. Please pay attention why TP-LINK Archer C6 doesn't route whereas Archer C2 does?

  0  
  0  
#10
Options
Re:Route configuration Archer C6
2021-09-11 16:42:29

@PKP 

 

You wrote:

"Ping from 192.168.2.* to internet works with TP Link Archer C2, but not with Archer C6. Same configuration."

I really can't say why's that. It needs some troubleshooting.

Try these two:

ping google.com

then

ping 8.8.8.8

Does any of those two receiving a replies ?

If the second ping command is receiving replies, then this would be a DNS problem - try setting a different DNS server in Ubiquity LAN settings (like 8.8.8.8 and 8.8.4.4).

If there's no replies from both ping commands, then observe what's the GW of the devices connected to Ubiquity and change it from 192.168.2.1 to 192.168.1.1 (if possible)

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#11
Options

Information

Helpful: 0

Views: 2608

Replies: 10

Related Articles
 Archer C6 configuration page issue
848 0
 Archer C6 VLAN ID Unable to Configure
914 0
 Configure a default route without using WAN
715 0
 Archer C6 Firmware v1.3.4 failed to back up device configuration
1143 0
 Archer C1200 static route does not work
505 0
Archer C6 limiting the internet connection to 100mbps
2620 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.