Home

Forums

Stories

Knowledge Base

Home Network Community > Deco > p7 disconnect

< Deco

p7 disconnect

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

p7 disconnect

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

p7 disconnect

katek8

2019-03-20 16:33:45 - last edited 2019-03-20 16:37:59

Posts: 3

Helpful: 13

Solutions: 0

Stories: 0

Registered: 2019-03-20

p7 disconnect

2019-03-20 16:33:45 - last edited 2019-03-20 16:37:59

Model: Deco P7

Hardware Version: V6

Firmware Version: 1.2.0

I have been using 3 p7 for now.

modem wired-> main p7(A) wired-> (tplink 8ports desktop switch) wired-> p7(B)

powerlined-> p7(c)

Most of the time, all p7 works prefectly.

I do gaming (low ping), no problem for streaming videos

but my second p7, the p7(B) keep disconnecting (flashing red) for approximately 10-30 seconds, and then reconnect.

Can someone help me to fix this problem?

Consider both P7(A) and P7(B) are both wired backhauled, except P7(C) is the only device using pure powerline (no mutual wifi connection or wire at all).

P7(A) and P7(C) works fine, P7(B) keep disconnecting???

3 Reply

Kevin_Z

2019-03-21 01:26:46

Posts: 21750

Helpful: 5135

Solutions: 2565

Stories: 21

Registered: 2018-12-24

Re:p7 disconnect

2019-03-21 01:26:46

Hi,

How often it drops internet?

Please tell us the Mac address of the P7 B unit.

Meanwhile, it is suggested to hard reset the P7 B unit and reconfigure it ; And you can exchange the location of P7 B unit and C unit and test whether the P7 B unit works.

Any updates, please let me know.

Have a good day.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

katek8

LV1

2019-03-21 16:52:52

Posts: 3

Helpful: 13

Solutions: 0

Stories: 0

Registered: 2019-03-20

Re:Re:p7 disconnect

2019-03-21 16:52:52

Thanks Kevin for your quick response

my P7(B) Mac address is: 0C-88-63-C7-C8-AC

it does not happen often (can perform well for the whole night), but once it happen to disconnect and reconnect, it usually happen few more times within an hour.

So basically I cant do gaming :(, the reconnection takes around 10 seconds or 30 seconds

And Yes, I have reset all 3 p7 devices and do the initial setup all over again. And try to switch between p7 devices.

That p7(B) location problem still happens, no matter I switch with p7(A) or p7(C).

I assume it can be a problem (maybe firmware?) for using wire backhaul?

Thank You

Kevin_Z

2019-03-25 01:14:57

Posts: 21750

Helpful: 5135

Solutions: 2565

Stories: 21

Registered: 2018-12-24

Re:Re:Re:p7 disconnect

2019-03-25 01:14:57

Hello Katek8,

Thanks for your reply, per you said, all the 3 decos have the same problem when they are located at P7 B location, it seems that the location affects the performance of P7 B a lot.

It is suggested to change another place to locate it to give it a shot.

Any updates, just let us know.

Good day.

p7 disconnect

p7 disconnect

Information

Voters 0

Tags