Home Network Community > Wi-Fi Routers > TL-WR941HP - led-controller[1014]: <6> 288051 Start to run WAN0_OFF
< Wi-Fi Routers

TL-WR941HP - led-controller[1014]: <6> 288051 Start to run WAN0_OFF

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12345

TL-WR941HP - led-controller[1014]: <6> 288051 Start to run WAN0_OFF

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
44 Reply
Re:TL-WR941HP - led-controller[1014]: <6> 288051 Start to run WAN0_OFF
2020-12-27 05:42:59

I have the same logs, nonstop LED Controler.

 

Internet lose connection every few minutes and CPU is almost always above 80% while nothing is happening.

 

It's an expensive router and It's very depressing that tp-link isn't helping with it.

 

I'll try reverting to an earlier firmware,,,

  0  
  0  
#32
Options
Re:TL-WR941HP - led-controller[1014]: <6> 288051 Start to run WAN0_OFF
2020-12-27 06:59:41 - last edited 2020-12-27 07:07:02

I just did a factory reset and this is all I see.

Internet still missing pings every now and then.

 

I couldn't give two fks about what that Led Controller is doing, I don't see the LED on my router.

  2  
  2  
#33
Options
Re:TL-WR941HP - led-controller[1014]: <6> 288051 Start to run WAN0_OFF
2021-01-14 22:50:50

I have the same problem, I took it 2 times to the warranty and they tell me that there is no problem. But the wifi is constantly cut off, when checking the log I see the message Start to run WAN0_OFF. It is at the latest level of firmware. I need a solution.

  2  
  2  
#34
Options
Re:TL-WR941HP - led-controller[1014]: <6> 288051 Start to run WAN0_OFF
2021-08-03 17:22:55 - last edited 2021-08-05 17:23:17

I have the same problem, but my router is TP-Link AX5400,Archer AX73.

  1  
  1  
#35
Options
Re:TL-WR941HP - led-controller[1014]: <6> 288051 Start to run WAN0_OFF
2021-08-03 18:14:31

Hi, I´ve found the solution, I threw the router into the trash can and bought a really good one, from another brand, because the tp-link support is not responding.

  7  
  7  
#36
Options
Re:TL-WR941HP - led-controller[1014]: <6> 288051 Start to run WAN0_OFF
2021-08-05 03:26:29

@gavin-cui 

 

Since the model is totally different, it's suggested to open a new thread describing the issue in detail.

 

Additionally, you can refer to this article we updated below to do basic troubleshooting first:

[Troubleshooting] Router Disconnects from Internet

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#37
Options
Re:TL-WR941HP - led-controller[1014]: <6> 288051 Start to run WAN0_OFF
2021-10-17 18:16:13

I have the same problem (WAN0_OFF message, disconnected almost every hour now). Bought the wr941hp last week.

 

Still no solution? @Kevin_Z 

  1  
  1  
#38
Options
Re:TL-WR941HP - led-controller[1014]: <6> 288051 Start to run WAN0_OFF
2021-10-17 18:25:45

Hi @deepbluesy no, sorry, the only solution I found was to buy a router from another brand. TP-Link support was pretty bad.

  2  
  2  
#39
Options
Re:TL-WR941HP - led-controller[1014]: <6> 288051 Start to run WAN0_OFF
2021-10-18 05:48:00

@deepbluesy 

 

Refer to this article we updated below to do basic troubleshooting first:

[Troubleshooting] Router Disconnects from Internet

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#40
Options
Re:TL-WR941HP - led-controller[1014]: <6> 288051 Start to run WAN0_OFF
2021-10-18 09:34:41

 

Kevin_Z wrote

@deepbluesy 

 

Refer to this article we updated below to do basic troubleshooting first:

[Troubleshooting] Router Disconnects from Internet


Followed that article still no luck.


I turn off the Wi-Fi using Wi-Fi button and turn it on again instead restarting router via power button. Maybe the Wi-Fi setting causing the problem? 

  1  
  1  
#41
Options
12345
Related Articles
TL-WR941HP
822 0
 Red LED color on my TL-WR941HP V1
808 0
 TL-WR941HP V2 WAN Orange LED
3214 0
 my TP-Link TL-WR941HP is nor workiing, only PWR led is on
2445 0
TL WR941HP chromecast issue
1100 0
 Tl wr941hp
714 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.