C5400 v2 only half speed on gigabit internet
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hardware Version :
Firmware Version :
ISP :
I have a gigabit internet connection. Speedtest gives mee 900+ Mbps when wired directly to my modem. Tested with laptop and Apple TV 4K.
A brand new Archer C5400 v2 only provides half the speed - with the same devices wired to it. Cat 6 cables in all tests.
Speedtest from the "Thether" app also shows connection speeds around 4-500 Mbps both up and down - I guess this should test the speed between router and modem.
So - is my Archer a defect unit, or are there fixes for this?
Regards,
Steinar Carlsen
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
This issue was driving me crazy for MONTHS. So glad I found this forum. Why would you put in a feature that clearly screws up the speed? Just wow. Turned all of this off and now no issues. All wireless (streaming) devices were also having problems maintaining their streams.
- Copy Link
- Report Inappropriate Content
So what did you do that fixed so the speed in WIFI will always get full speed ?
- Copy Link
- Report Inappropriate Content
i have the same problam ? so any company update respond ? and can the vactory replace for me to new router ?
- Copy Link
- Report Inappropriate Content
Same issue here.
TP-Link Archer C5400X
Able to get gigabit Internet WAN speeds after rebooting the router. Wait a couple hours and the speed drops to less than half-gigabit (around 400 Mbps). Rebooting the router every few hours just to maintain gigabit speeds isn't an option.
Cat 6 Ethernet hardwire install from the router to the computer running Speedtest
Application Priority is set to "Normal" for the gaming, streaming, surfing, chatting and downloading options
Device Priority is normal for all devices
Firmware version: 1.1.0 Build 20180904 rel.41828(5553)
Hardware version: ArcherC5400X v1.0
This problem has been reported numerous times in this forum, so it doesn't look like an isolated event.
In summary, when the router Internet WAN speed maxes out at around 400 Mbps with gigabit Internet service, rebooting the router resolves the issue for a couple hours.
You can say I'm not a satisfied customer.
- Copy Link
- Report Inappropriate Content
Hi,
That is a little complicated, our engineer has contacted you via email, if you are willing to do further troubleshooting, please notice your inbox.
Good day.
rtpbiker wrote
Same issue here.
TP-Link Archer C5400X
Able to get gigabit Internet WAN speeds after rebooting the router. Wait a couple hours and the speed drops to less than half-gigabit (around 400 Mbps). Rebooting the router every few hours just to maintain gigabit speeds isn't an option.
Cat 6 Ethernet hardwire install from the router to the computer running Speedtest
Application Priority is set to "Normal" for the gaming, streaming, surfing, chatting and downloading options
Device Priority is normal for all devices
Firmware version: 1.1.0 Build 20180904 rel.41828(5553)
Hardware version: ArcherC5400X v1.0
This problem has been reported numerous times in this forum, so it doesn't look like an isolated event.
In summary, when the router Internet WAN speed maxes out at around 400 Mbps with gigabit Internet service, rebooting the router resolves the issue for a couple hours.
You can say I'm not a satisfied customer.
- Copy Link
- Report Inappropriate Content
Qatar wrote
i have the same problam ? so any company update respond ? and can the vactory replace for me to new router ?
Hi, what is the model number of your device?
Could you please show us more details about the current speed issue and then we can give you a specific answer.
Good day.
- Copy Link
- Report Inappropriate Content
This is an old thread but here was my issue with the c5400.
ISP - Cox
Speed Tier - gigablast
It worked fine at first. About a month in I noticed that the internet was starting to lag down. Ran speed tests and was only getting about 300 mbs ar each computer attached to the router. I did have a asus router in repeater mode in a seperate room as a wireless bridge for another wired device. This was the setup I was running from day one. I chatted with a tp link agent and multiple cox agents over the course of 6 months trying to figure out the issue. The speeds kept dropping. The entire time I was getting about 850 to 900 directly hooked to the modem. I finally ended up replacing the c5400 with the asus router. Speeds are coming through nicely.
I honestly believe there is a bad batch of modems out there as I have a friend that has the exact same setup as I have and has had zero problems with speed... I will not be using tplink products again due to poor quality and poor customer service.
- Copy Link
- Report Inappropriate Content
@sca- Copy Link
- Report Inappropriate Content
Hi @sca and all,
Regarding the half-speed issue of Archer C5400 V2, we attached great importance on it and we have released a firmware which you can install and take some time to verify whether it works.
You can click here to get the beta firmware. Once you downloaded it, you can take some time to install it and test the performance.
Wish you all have a good day.
- Copy Link
- Report Inappropriate Content
@Kevin_Z could you post the link in this thread?
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 21415
Replies: 87
Voters 0
No one has voted for it yet.