Home Network Community > Wi-Fi Routers > Archer C3200 V1 not possible to set LAN IP to subnet 1. (LAN to WAN)
< Wi-Fi Routers

Archer C3200 V1 not possible to set LAN IP to subnet 1. (LAN to WAN)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer C3200 V1 not possible to set LAN IP to subnet 1. (LAN to WAN)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer C3200 V1 not possible to set LAN IP to subnet 1. (LAN to WAN)
Archer C3200 V1 not possible to set LAN IP to subnet 1. (LAN to WAN)
2020-12-22 14:20:53 - last edited 2020-12-22 15:25:52
Model: Archer C3200  
Hardware Version: V1
Firmware Version: 0.9.1 0.1 v004b.0 Build 160712 Rel.55313n

When i go to Advance/Network/LAN the standard ip address is 192.168.0.1 when i set the ip address to 192.168.1.2 and hit apply the router reboots and comes back with the standard ip address 192.168.0.1 i tried everything i also did a factory reset but noting works this router doesn't accept a different subnet i think that this is a bug in the firmware.

Is it possible to fix this with a firmware update?

 

I have it set up in LAN/WAN, cable from modem LAN to router WAN, i want the router in the same subnet as the modem but this doesnt work.

 

  0      
 
  0      
 
#1
Options
9 Reply
Re:Archer C3200 V1 not possible to set LAN IP to subnet 1. (LAN to WAN)
2020-12-23 15:04:00

@Erwin05 

 

Are you trying to use your C3200 as an access point ?

You can have both LAN IP address of your C3200 and your modem, only when using them in this scenario.

 

 

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#2
Options
Re:Archer C3200 V1 not possible to set LAN IP to subnet 1. (LAN to WAN)
2020-12-23 17:01:03 - last edited 2020-12-23 17:12:13

@Ivaylo 

 

Yes, i know how to set it up in LAN/LAN.

 

On the internet some 1 sets it up in LAN/WAN with 2 TP link routers but they both have the same subnet 0 and this works.

 

https://hetmanrecovery.com/recovery_news/connection-of-2-routers-in-one-network-wifi-gain-shared-resources.htm#plan_5

 

But my router has a different subnet then my modem and then this doesnt work.

  0  
  0  
#3
Options
Re:Archer C3200 V1 not possible to set LAN IP to subnet 1. (LAN to WAN)
2020-12-23 18:04:46 - last edited 2020-12-23 19:58:59

@Erwin05 

 

It's best to watch the YouTube video for the instructions.

The article following the video tutorial is poorly written. Some of the screenshots are not real examples.

See <Jake 10.04.2020 21:18> comment : https://hetmanrecovery.com/recovery_news/connection-of-2-routers-in-one-network-wifi-gain-shared-resources.htm/#comment-7032

Obviously you can't have an IP address range ending at 192.168.0.299

 

Moreover,

Watching the video instructions (LAN/WAN scenario) you can clearly see:

@10:57 (LAN IP address of the first router is 192.168.0.1)

@11:22 (LAN IP address of the second router is 192.168.1.1)

Their LAN IP addresses are in different networks.

 

You can configure them both - LAN/LAN or LAN/WAN (following the video instructions), but I would recommend LAN/LAN, thus avoiding double NAT in your network.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  1  
  1  
#4
Options
Re:Archer C3200 V1 not possible to set LAN IP to subnet 1. (LAN to WAN)
2020-12-23 18:49:37 - last edited 2020-12-23 19:15:04

@Ivaylo 

 

LAN/WAN only works if the router keeps his own IP address 192.168.0.1 but then i have 2 networks.

 

So it is not possible to do LAN/WAN to set the router to 192.168.1.2 in the same subnet as the modem if the router uses standard subnet 0.

Maybe it would work if i had a router with standard subnet 1.

 

My setup:

Modem has ip address 192.168.1.1 range start at 192.168.1.10 to 192.168.1.210

Router set to ip address 192.168.1.2 at range 192.168.1.211 to 192.168.1.254

This is how they explane it op on that site.

 

After connecting the wan cable to the router it reboots and is set back to 192.168.0.1

 

On the site they talking about in the same subnet and that doesnt work.

 

 

 

  0  
  0  
#5
Options
Re:Archer C3200 V1 not possible to set LAN IP to subnet 1. (LAN to WAN)
2020-12-23 19:11:54 - last edited 2020-12-24 00:47:29

That was exactly my point. If you have your modem LAN in 192.168.1.X then the WAN port of your C3200 can be set as 192.168.1.2 (for example).

But... its LAN can't be in the same network - 192.168.1.X because it makes a NAT to a different network by default - as you said keeps reverting to 192.168.0.X network.

The only way to do this (if at all possible), is if you can disable NAT of your C3200. Check that in your router and if you do have it, then uncheck Enable NAT option and try again.

If you don't have that feature implemented then you can't do that, the way you want.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  1  
  1  
#6
Options
Re:Archer C3200 V1 not possible to set LAN IP to subnet 1. (LAN to WAN)
2020-12-23 19:22:42 - last edited 2020-12-23 19:34:15

@Ivaylo 

 

I only see in the menu under NAT forwarding: ALG, Virtuele server, poort triggering, DMZ, UPnP

 

So i only can set this router in LAN/LAN.

 

  0  
  0  
#7
Options
Re:Archer C3200 V1 not possible to set LAN IP to subnet 1. (LAN to WAN)
2020-12-23 19:30:25 - last edited 2020-12-23 22:38:08

@Erwin05 

 

This is a screenshot from another router model (just as an example):

 

If you don't have such an option in your management interface, then you can't disable NAT feature of C3200 - not every TP-Link router model got that implemented.

In the recent router models (not all devices) there's a dedicated operation mode - AP. In this scenario your connection would be LAN/WAN and the IP address of the WAN port (called LAN in this mode) - that's the blue port - should be in the same network as the modem LAN ports. But that's not the C3200 case.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#8
Options
Re:Archer C3200 V1 not possible to set LAN IP to subnet 1. (LAN to WAN)
2020-12-23 19:40:46 - last edited 2020-12-23 19:51:29

@Ivaylo 

 

No, this router doesnt have that option.

 

And if this router would have a standard IP address with subnet 1 so 192.168.1.1 then this would work? I believe Asus router have a ip address 192.168.1.1

 

  0  
  0  
#9
Options
Re:Archer C3200 V1 not possible to set LAN IP to subnet 1. (LAN to WAN)
2020-12-23 20:07:21 - last edited 2020-12-24 01:45:56

That's not the point, because you can change the LAN IP address of C3200 to be 192.168.1.1. But the WAN IP address can't be in the same network (192.168.1.X) and vise versa. In short, configure the LAN/LAN scenario (the link from my first post or the YouTube tutorial from the article) and everything would be fine.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#10
Options

Information

Helpful: 0

Views: 2296

Replies: 9

Related Articles
 Bricked Archer C3200 V1
1232 0
 archer c3200 set as an Acces Point
2769 0
Archer c3200 restart automatically
1141 0
 Archer C3200 will not connect to No-IP DDNS account
1096 0
 TP Link Archer C3200
1089 0
 Archer C3200 - how to set up QoS
2046 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.