Home Network Community > Wi-Fi Routers > Bandwidth constraint for Guest network
< Wi-Fi Routers

Bandwidth constraint for Guest network

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Bandwidth constraint for Guest network

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Bandwidth constraint for Guest network
Bandwidth constraint for Guest network
2020-03-15 07:34:32 - last edited 2021-07-29 11:33:48
Model: Archer A5  
Hardware Version: V4
Firmware Version:

Hi,

 

I have an Archer C50 (V4) and want to set bandwidth control on my Guest Network. The manual says "The range of bandwidth for guest network is calculated according to the setting of Bandwidth Control on the Bandwidth Control page." However, when I check this page, it simply provides a facility for setting bandwidth controls by IP addresses.

 

Do I take it that the entire Guest network, irrespective of the assigned IP addresses, will be throttled to whatever is set in the Bandwidth Control page?

 

TIA - Peter

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Bandwidth constraint for Guest network-Solution
2020-03-16 09:20:37 - last edited 2021-07-29 11:33:48

@PeterJ 

 

To enable bandwidth control for guest network, you need go to Bandwidth control page to enable it and enter the Egress/Ingress bandwidth. 

Note: You can enter the actual bandwidth you paid for your ISP.

  • Egress Bandwidth - The max upload speed which through the WAN port.
  • Ingress Bandwidth - The max download speed which through the WAN port.

 

Then you can setup the detailed information for the bandwidth control of guest network. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
1 Reply
Re:Bandwidth constraint for Guest network-Solution
2020-03-16 09:20:37 - last edited 2021-07-29 11:33:48

@PeterJ 

 

To enable bandwidth control for guest network, you need go to Bandwidth control page to enable it and enter the Egress/Ingress bandwidth. 

Note: You can enter the actual bandwidth you paid for your ISP.

  • Egress Bandwidth - The max upload speed which through the WAN port.
  • Ingress Bandwidth - The max download speed which through the WAN port.

 

Then you can setup the detailed information for the bandwidth control of guest network. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 845

Replies: 1

Related Articles
Guest Network Bandwidth Control
1319 0
MR600 how to limit the Bandwidth of the guest network
11600 0
Router with guest network with bandwidth limit
1190 0
Guest Network Bandwidth Control of Archer C80
1343 0
Control bandwidth to individual users in guest network
391 0
 Bandwidth control on guest network.
695 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.