Home

Forums

Stories

Knowledge Base

Home Network Community > DSL Modem Routers > MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz

< DSL Modem Routers

MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TheRiddle

2019-12-09 09:17:20 - last edited 2019-12-10 03:26:12

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2019-12-09

MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz

2019-12-09 09:17:20 - last edited 2019-12-10 03:26:12

Model: AC50

Hardware Version: V1

Firmware Version: 181217

Good morning,

MODEL ARCHER VR1200 V.1.0

I performed the installation as instructed.
I have done the firmware upgrade.
I have tried several times to reset to factory settings and to repeat the installation.
Nevertheless the result does not change.
All the devices connected in 5Ghz correctly browse the internet while for devices connected in 2.4ghz (any OS: windows, linux, android) it is showed that internet connection is not available. I can't even connect to the TPLink configuration interface even if connected in 2.4ghz.
In the control panel the wifi in 2.4ghz is correctly enabled (default settings).
In some cases, although everything is enabled, the 2.4ghz channel is not detected by the devices and not even the light on the modem is on (while for the 5. ghz there are no problems).

How could I solve?

2 Reply

ArcherC8

LV5

2019-12-09 14:03:28 - last edited 2019-12-10 03:26:12

Posts: 2138

Helpful: 858

Solutions: 51

Stories: 0

Registered: 2018-11-05

Re:MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz

2019-12-09 14:03:28 - last edited 2019-12-10 03:26:12

@TheRiddle You may have bad unit. First try changing the channel from auto to one of the available channels and also the channel width. You may be on a channel that has some type of interference in your house. Do not hide SSID (enable) and use different SSID names. Be sure the mode is 11bgn. Leave WDS off for now. Disable any MAC filtering.

Kevin_Z

2019-12-10 03:25:54 - last edited 2019-12-10 03:26:12

Posts: 21773

Helpful: 5142

Solutions: 2574

Stories: 21

Registered: 2018-12-24

Re:MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz

2019-12-10 03:25:54 - last edited 2019-12-10 03:26:12

@TheRiddle

Please ensure that the 2.4GHz wifi network has been enabled and do not hide SSID; try to change the wireless settings to give it a go, including the wireless network name and channel, like channel 1, 6 and 11.

When it is connected but no internet access, please click here to get the IP address and gateway.

And then try to ping the gateway of the Archer VR1200, which is 192.168.1.1 by default and show us the results.

Try to change another wireless device to verify whether it has the same issue. And ensure that the firmware of the VR1200 is up to date.

Besides, when and where did you buy this Archer VR1200?

Good day.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz

MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz

Information

Voters 0

Tags