Home Network Community > Deco > Question about network mix with P7 and M5
< Deco

Question about network mix with P7 and M5

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Question about network mix with P7 and M5

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Question about network mix with P7 and M5
Question about network mix with P7 and M5
2019-12-06 07:54:33

Hi,

 

Can you place a P7 not as main deco? but in the middle of a deco chain?

 

I have a house with a dependency. Tto reach the Guest house, (wifi is to far) the only way is PLC. but I can not plug the main P7 next to the router because the PLC would not reach the guest house different electric line. My only way is to plug a P7 PLC at the far end of the house and then it communicates with the guest house.

 

Would this work?

 

Thank you for your help

 

  0      
 
  0      
 
#1
Options
5 Reply
Re:Question about network mix with P7 and M5
2019-12-09 02:18:30

@Jojo42 

 

Hello, theoretically, you can locate them like the picture attached to boost the wifi signal. 

 

While cause the Deco P7 is located far end of the house, the signal strength between the P7 and main Deco M5 will be affected a lot, so the whole mesh network performance would be affected correspondingly. 

 

Meanwhile, may I know how far bwteen the main house and the guest house? 

 

Good day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Question about network mix with P7 and M5
2019-12-09 06:28:17

@Kevin_Z 

 

Thank you for your answer Kevin

 

I have updated the diagram, as I am trying to optimise the network setup. Both Wifi Links will be line of sight and less than 30 feet away. But for the wired ethernet and PLC Backhaul I still have a doubt...

 

I read that ethernet and PLC backhaul could not work concurrently. But is this for a whole mesh network or only between 2 units.

 

Please see the attached diagram it is self explanatory, will both the ethernet (Between the 2 Deco M5) and the PLC (Between the 2 P7) backhaul work on this network?

 

Thank you for you help.

 

Geoffroy

  0  
  0  
#3
Options
Re:Question about network mix with P7 and M5
2019-12-10 02:11:55

@Jojo42 

 

For your question, it is for the connection between 2 units only, compared with wifi backhaul and PLC backhaul, the performance of ethernet backhaul will be better due to the less interferences. Therefore it has higher priority. 

 

The diagram attached is good, you can connect them and use the powerline backhaul to build up the mesh network to boost the wifi and enlarge the wifi coverage area. 

 

While considering the wifi signal seems to be weak due to the distance, even though the powerline backhaul takes effect, the performance of the further Deco P7 would be affected to some extent. 

 

May it help. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options
Re:Question about network mix with P7 and M5
2019-12-10 06:57:27

@Kevin_Z 

 

Thanks a lot. I will install next week and give feedback on this mesh config performance.

 

best regards

Geoffroy

  0  
  0  
#5
Options
Re:Question about network mix with P7 and M5
2019-12-10 12:02:26

@Jojo42 

 

Definitely sure. Just take your time to instal and test the performance. 

 

If need any further help, be free to let me know. 

 

Good day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 1233

Replies: 5

Related Articles
 Can you mix Deco M5 and P7 in one Mesh Wi-Fi system?
2067 0
Can you mix deco m5 v1 with a v2 or v3?
1088 0
 Deco M5 network question
490 0
 Mix with Deco M4 and M5
4915 0
Deco M5 not working with P7
1727 0
Mix and Match
457 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.