Omaha policy routing by MAC address instead of static ip?
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Can I set up policy routing on a multi wan omada router categorising devices by MAC address instead of LAN ip? The reason is that I already have the MAC addresses of all my devices static and I'll have to assign IP's statically to each of them
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi @14paavang
Thanks for posting in our business forum.
Configuration should be layer 1 > layer 2 > layer 3. Policy routing is about configuring L3 and NAT and it should be IP, not MAC address. MAC can bind to the IP though.
- Copy Link
- Report Inappropriate Content
Hi @14paavang
Thanks for posting in our business forum.
Configuration should be layer 1 > layer 2 > layer 3. Policy routing is about configuring L3 and NAT and it should be IP, not MAC address. MAC can bind to the IP though.
- Copy Link
- Report Inappropriate Content
speaking of nat, if I'm running a dual nat setup, can I still use policy routing if my Omada router is on the second layer? I.e if I have a er605 connected to a few decos but I kept them in router mode, when UK's I still be able to see all the devices individually connected to the deco mesh? I'm asking as I currently have qos set up on my decos and when I add an er605, I still need to be able to do that
- Copy Link
- Report Inappropriate Content
Hi @14paavang
Thanks for posting in our business forum.
14paavang wrote
speaking of nat, if I'm running a dual nat setup, can I still use policy routing if my Omada router is on the second layer? I.e if I have a er605 connected to a few decos but I kept them in router mode, when UK's I still be able to see all the devices individually connected to the deco mesh? I'm asking as I currently have qos set up on my decos and when I add an er605, I still need to be able to do that
I don't understand what you mean by the second layer. Double-NAT should be setting the uplink as bridge mode and it should be fixed.
To see what's connected to the Deco, you should turn Deco into AP mode.
If you keep the Deco in router mode, you don't have any possibility to see what's behind it because of the essence of NAT.
- Copy Link
- Report Inappropriate Content
@Clive_A so all I have to do is make an er605 be in bridge mode and have 2 wans and then connect me decks in router mode to the er605 and then I get to keep the deco qos
- Copy Link
- Report Inappropriate Content
Hi @14paavang
Thanks for posting in our business forum.
14paavang wrote
@Clive_A so all I have to do is make an er605 be in bridge mode and have 2 wans and then connect me decks in router mode to the er605 and then I get to keep the deco qos
There is no bridge mode on the ER605. None TP-Link models except for the DSL models have that. Deco and Omada are both routers expcet for the ER605 is supposed to be the NAT.
Consider either replacing the Deco and use them as AP. Or use the Deco with the modem.
- Copy Link
- Report Inappropriate Content
@Clive_A so decos in ap mode then and then I have to assign static IPs to all the clients so I can policy route them properly
also does policy routing get overriden when the network has to fail to the secondary wan?
- Copy Link
- Report Inappropriate Content
Hi @14paavang
Thanks for posting in our business forum.
14paavang wrote
@Clive_A so decos in ap mode then and then I have to assign static IPs to all the clients so I can policy route them properly
also does policy routing get overriden when the network has to fail to the secondary wan?
Please try out the guide first and read about each parameter in the help center(?). Will discuss this with you if you have other questions.
- Copy Link
- Report Inappropriate Content
@Clive_A which guide is this now ?
- Copy Link
- Report Inappropriate Content
Hi @14paavang
Thanks for posting in our business forum.
14paavang wrote
@Clive_A which guide is this now ?
There is a list of configuration guides on the forum. Same for the FAQ. Please refer to the existing guides and manuals. Policy Routing as the keywords, you will have several guides about this.
And in the configuration page, you have the help center for explanation about every term in the parameters.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 535
Replies: 9
Voters 0
No one has voted for it yet.