Switches Forums - Business Community

GeneralHowto - A Guide to Use Forum Effectively. Read Before You Post.

The topic was originally posted by Clive_A in Howto - A Guide to Use Forum Effectively. Read Before You Post. Hi, if you are new to the forum, we would love to show your how to use our forum and make

By

Clive_A

2Helpful

452Views

0Replies

Configuration GuideHow to Set Up QoS for Dante and Voice Protocols on Omada Switch

Background: This post provides a configuration guide to set up QoS on Omada Switch for Dante and voice-related protocols. This Article Applies to: Omada switches with the QoS feature. L2+ and L3 Switc

ControllerOfficialQoS

By

Clive_A · Latest post 3 weeks ago by KocherJJ

5Helpful

1931Views

4Replies

Early AccessOmada Switch Pre-Release Firmware (Released on Jun 11th, 2024)

This Article Applies to Model Hardware Version Firmware Version Firmware Date Rel Number TL-SL2428P V5 5.0.8 20240531 65965 TL-SL2428P V4 4.20.11 20240531 65965 TL-SG3428 V1 1.1.10 20240531 65965 TL-S

OfficialFirmware Update

By

Clive_A · Latest post 2024-12-05 00:49:23 by MrAdministrator

32Helpful

5312Views

17Replies

Configuration GuideHow to Shut Down the Switch Port Connected to an EAP to Prevent Intrusion via 802.1X Authentication?

Background: This post provides a configuration guide on how to configure 802.1X to allow only specific EAPs to get a network, thus blocking any other device from getting a connection from the same net

Configuration

By

Vincent-TP · Latest post 2024-11-05 01:43:36 by Vincent-TP

8Helpful

484Views

2Replies

Knowledge BaseHow to enter the BootUtil menu to reset TP-Link Managed Switch via Console Port

This Guide Applies to: All of TP-Link Managed Switches with a Console port. Introduction: TP-Link BootUtil menu enables some advanced features, such as activating the backup image, recovering the pass

OfficialHighlighted Thread

By

Fae · Latest post 2024-04-04 14:05:58 by Benjaminmark

10Helpful

10297Views

6Replies

How can i stop DHCP being served to a group of ports on one particular switch on a particular vlan?

I have need to prevent devices with a specific VLAN tag from receiving DHCP on a group of ports on one particular switch - they instead must be set as statics. I want to force this so the users must s

By GRL

0Helpful

26Views

0Replies

Need some help with Spanning Tree config

Hello folks I would like to enable spanning tree and link between my two main switches. Currently i have an "Aggregation" switch with a 10gbit link from my ER8411 to my SG3428X From the SG3428X i have

By GRL · Latest post Yesterday by Clive_A

0Helpful

42Views

1Replies

LLDP MAP

hi tplink, i'm having trouble with how the map shows the location of my switches. if you refer to the image image below, before this is the setup. however i since change the sx3008f to be the main, in

Configuration

By ImranRn · Latest post Wednesday by ImranRn

1Helpful

74Views

2Replies

Configuration GuideHow to Configure VLAN on TP-Link Switch

Background: This post provides a configuration guide to set up a VLAN-tagged and untagged port, PVID, and trunk on TP-Link switches. This Article Applies to: All Omada switches that support 802.1Q VLA

VLAN & Multi-NetworksOfficialConfiguration

By

Clive_A · Latest post Wednesday by 01967110624

4Helpful

9094Views

1Replies

Collapsed core setup? Switch as the center of the network.

I'm looking to do a bit more optimizing of our network. We have 2 switches and as you can see in the picture I want to utilize the 10G port on the switches as a backbone between the 2. The Synology NA

ConfigurationNetwork Connectivity

By NielsS · Latest post Wednesday by Clive_A

3Helpful

117Views

7Replies