Switches Forums - Business Community

GeneralHowto - A Guide to Use Forum Effectively. Read Before You Post.

The topic was originally posted by Clive_A in Howto - A Guide to Use Forum Effectively. Read Before You Post. Hi, if you are new to the forum, we would love to show your how to use our forum and make

By

Clive_A

1Helpful

328Views

0Replies

Configuration GuideHow to Shut Down the Switch Port Connected to an EAP to Prevent Intrusion via 802.1X Authentication?

Background: This post provides a configuration guide on how to configure 802.1X to allow only specific EAPs to get a network, thus blocking any other device from getting a connection from the same net

Configuration

By

Vincent-TP · Latest post a week ago by Vincent-TP

7Helpful

156Views

2Replies

Early AccessOmada Switch Pre-Release Firmware (Released on Jun 11th, 2024)

This Article Applies to Model Hardware Version Firmware Version Firmware Date Rel Number TL-SL2428P V5 5.0.8 20240531 65965 TL-SL2428P V4 4.20.11 20240531 65965 TL-SG3428 V1 1.1.10 20240531 65965 TL-S

OfficialFirmware Update

By

Clive_A · Latest post 3 weeks ago by GRL

27Helpful

3830Views

16Replies

Configuration GuideHow to Set Up QoS for Dante and Voice Protocols on Omada Switch

Background: This post provides a configuration guide to set up QoS on Omada Switch for Dante and voice-related protocols. This Article Applies to: Omada switches with the QoS feature. L2+ and L3 Switc

Controller RelatedOfficialQoS

By

Clive_A · Latest post 2024-10-02 14:53:33 by MichielD.

3Helpful

1084Views

3Replies

Knowledge BaseHow to enter the BootUtil menu to reset TP-Link Managed Switch via Console Port

This Guide Applies to: All of TP-Link Managed Switches with a Console port. Introduction: TP-Link BootUtil menu enables some advanced features, such as activating the backup image, recovering the pass

OfficialHighlighted Thread

By

Fae · Latest post 2024-04-04 14:05:58 by Benjaminmark

9Helpful

8985Views

6Replies

Blocking ARP packets on SG3428X-M2

I'm trying to block ARP packets from a specific IP range. I have tried seemingly every possible combination of ACL settings and none of them seem to affect ARP packets (0 packets matched when ethertyp

Switch ACL

By ekaszubski

0Helpful

15Views

0Replies

SX3206HPP fans spin up as soon as 10GBase-T device connected

Hi all My SX3206HPP spins up the fans audibly as soon as I connect a 10GBase-T device to it. Since the switch is in the office this is rather annoying. Limiting the port speed to 1000M will resolve th

By SvenT

0Helpful

20Views

0Replies

SG2008P LACP LAG for TrueNAS Core 13.0 on HP MicroServer Gen8

Hi all I am struggling to get the LAG working in my environment. I have ER605, OC200, 2x SG2008P and 2x EAP245. Also I have HP MicroServer Gen8 with TrueNAS CORE running on it with number of Jails. I

LAGConfigurationVLAN & Multi-Networks

By vrtareg · Latest post Yesterday by vrtareg

2Helpful

120Views

2Replies

Native vlan 1 change ID

Hi, I created a vlan ID 2 and I have to make the change with vlan 1. Then I have to disable the vlan 1.Which command line (CLI) should I set? Thanks for the help

By Sissilo · Latest post Wednesday by MR.S

3Helpful

186Views

13Replies

Connect Switch using Omada to a Fortigate FW 60 F

Good mornign I have a TL-SG3452P Switch and I want to replace Cisco old device. I have a OMADA Controller with several AP already configured in my laptop on VLAN 1. Also, I use a Fortigate 60 F as Rou

VLAN & Multi-NetworksController RelatedNetwork ConnectivityConfiguration

By Ericson574 · Latest post Wednesday by Clive_A

1Helpful

39Views

1Replies