Issue with C510W losing connection
Issue with C510W losing connection
Hi all,
I just bougth two Tapo C510W. Everything was OK during configuration and during initial tests.
I mounted the cameras outside (and they cannot be accessed in an easy way) and put power on them.
Just after the Camera checkup is finished, I can see the cameras connected to the dedicated access point, receiving an IP address and the network quality is at maximum level.
I can see them in the Tapo app too.
But... less than 30s later, both cameras disapears from network (and of course they get offline in the app)
Anyone with an idea what to do to solve this ?
Thanks in advance.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@archercj Just to give a feedback about the issue I had (maybe your's different)
I still have no idea about the root cause of the problem. But, using the cameras at exactly the same place and same conditions, both works fine now.
The reason was discovered by luck.
During my tests, I had to move a little bit the cameras to get a better access. Unfortunatly, the external fixed power cable I used (used to power also two halogen projectors) was a little but to short.
So I decided to use simple electric extension cord, connected on a plug in the room near the cameras. And the result was that everything worked fine !After reconnecting the cameras on the external power cable, same troubles starts again.
After testing this twice, each time I used the simple electrical cord it was OK.
I decided to laid a dedicated external power câble for the cameras.
Since then, they wor perfectly, Never disconnected from wireless network again.
Maybe my feedback will help.
- Copy Link
- Report Inappropriate Content
Hi,
The problem may be related to the Wi-Fi signal strength. Please try to power off the camera, power on it, and then check if it will reconnect to a Wi-Fi network and work.
If so, go to the camera's Device Settings>Device Info page, tap the Wi-Fi icon, and check if the RSSI value is good(more than -50dBm).
How about your network diagram, how far is between the camera and the router, or between the camera and the nearby AP?
Best Regards
- Copy Link
- Report Inappropriate Content
@Solla-topee Thanks for the reply.
The WiFi quality was the first way I followed. That's why, to definitely eliminate this risk, I setup a dedicated accesspoint just near the cameras. Cameras are less than 2 meters from the AP, and there is no wall between them, just a simple window.
I tried several times to restart the cameras (I'm working on the issue since 2 days :/( ) , expecting it would be OK. But each time the connection is lost (more or less) 30s after the restart. It's difficult to access the camera parameters between this time. In the app, when they switch from "offline" to "OK", I just have the time to go in the configuration menu, the configuration menu is displayed, and just after that few seconds, the connection is lost.
But the AccessPoint shows the connection quality (in term of number of lines displayed on the WiFi logo). As you can see in the screenshot, connection is OK.
I just retried (one more time) 2 hours ago to restart the cameras. I saw that the connection quality, after being great just after the restart drops on a low level (just 1 bar displayed on the AP WiFi logo) just before the connection is lost. I don"t know if the connection quality really drops down, or of it's just the refresh time of the display that act in this ways and shows just one bar, but in reality the connection is already lost at this time
- Copy Link
- Report Inappropriate Content
Hi,
Is the Archer AX55 the access point, or is it the wireless router and another access point connects to it and near the camera?
If the Archer AX55 is the wireless router, your camera is connected to the router's Wi-Fi rather than the nearby AP, and it may be why it loses connection soon after powering on.
Best Regards
- Copy Link
- Report Inappropriate Content
@Solla-topee The archer AX55 is configured as access point and is the access point near the cameras.
- Copy Link
- Report Inappropriate Content
Hi,
If the AP(AX55) and wireless router have the same SSID, please try the following steps and check if they will help.
1. Log in to the AP's web UI to change the 2.4G SSID different from the wireless router.
2. Unmount a camera from the outside location, put it close to the AP, factory reset it, and reconfigure it.
3. Test if the camera will work fine for 30 minutes. If yes, mount it again and check if it will work fine.
Best Regards
- Copy Link
- Report Inappropriate Content
@Solla-topee Hi,
SSIDs are different. The SSID on the AX55 is unique, only for these two cameras.
Today I tested the link quality from AX55 to internet (I connected a smartphone by Wifi to the AX55). I did 10 speedtests during the day at different moments. The worst results were a little bit over 20Mbits/s (in both directions)
The physical unmount (I did it once with the same results) isn't easy to do. I have to rent a bucket truck to get access to the cameras. Unfortunatly, I tried after a facotry reset, tested (too quickly:/ ) the connection and it was OK. So I mounted both cameras expecting result would be OK.
If there is not other way to follow, I will have to rent the truck :/
- Copy Link
- Report Inappropriate Content
Hi,
I have reported the issue to the tech team, and they will likely reach out to you via email to continue troubleshooting your issue. Please check your email box and confirm.
Best Regards
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@TheYoda You are welcome~
- Copy Link
- Report Inappropriate Content
@Solla-topee did you ever resolve this. I am about to throw my C510W in the bin. Had no end of connection issues. I believe there is an issue with the device communicating with a router.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 1714
Replies: 18
Voters 0
No one has voted for it yet.