Switches Forums - Business Community

GeneralHowto - A Guide to Use Forum Effectively. Read Before You Post.

The topic was originally posted by Clive_A in Howto - A Guide to Use Forum Effectively. Read Before You Post. Hi, if you are new to the forum, we would love to show your how to use our forum and make

By

Clive_A

1Helpful

342Views

0Replies

Configuration GuideHow to Shut Down the Switch Port Connected to an EAP to Prevent Intrusion via 802.1X Authentication?

Background: This post provides a configuration guide on how to configure 802.1X to allow only specific EAPs to get a network, thus blocking any other device from getting a connection from the same net

Configuration

By

Vincent-TP · Latest post 2 weeks ago by Vincent-TP

7Helpful

199Views

2Replies

Early AccessOmada Switch Pre-Release Firmware (Released on Jun 11th, 2024)

This Article Applies to Model Hardware Version Firmware Version Firmware Date Rel Number TL-SL2428P V5 5.0.8 20240531 65965 TL-SL2428P V4 4.20.11 20240531 65965 TL-SG3428 V1 1.1.10 20240531 65965 TL-S

OfficialFirmware Update

By

Clive_A · Latest post 2024-10-24 08:49:16 by GRL

30Helpful

4017Views

16Replies

Configuration GuideHow to Set Up QoS for Dante and Voice Protocols on Omada Switch

Background: This post provides a configuration guide to set up QoS on Omada Switch for Dante and voice-related protocols. This Article Applies to: Omada switches with the QoS feature. L2+ and L3 Switc

Controller RelatedOfficialQoS

By

Clive_A · Latest post 2024-10-02 14:53:33 by MichielD.

4Helpful

1186Views

3Replies

Knowledge BaseHow to enter the BootUtil menu to reset TP-Link Managed Switch via Console Port

This Guide Applies to: All of TP-Link Managed Switches with a Console port. Introduction: TP-Link BootUtil menu enables some advanced features, such as activating the backup image, recovering the pass

OfficialHighlighted Thread

By

Fae · Latest post 2024-04-04 14:05:58 by Benjaminmark

9Helpful

9114Views

6Replies

SG3210X-M2 - After Firmware-Update to 1.0.5 (and Reboot), Switch is Disconnected

Hello, today was the Firmware-Update-Day in my Omada-Network. For my SG3210X-M2 V1 Switch was the newest Firmware-Version 1.0.5 (previous Firmware was 1.0.3). The Firmware-Update Start was proceeded b

Firmware UpdateController RelatedAdopting

By NeoMorpheus

0Helpful

30Views

0Replies

[SG3218XP-M2] Permit ACL with IP-Port or IP (protocol not ALL) not working

ACL setup IP-Port Group: Nginx 443 IP Group: Nginx Issue: I can't access Nginx homepage with this setup. Wireguard captured packets Everything work just fine once I disable ACL rule 11 and 12. Expecte

Switch ACL

By yliu

0Helpful

41Views

0Replies

Omada Controller attached switches showing wrong or missing IP's

Hi, I have built an OMADA network connecting over 80 devices using two TL-SL2428P managed switches and an EAP610-Outdoor. Omada Controller mapped all device MAC’s and IP to each switch and port, howev

By Garyghj

0Helpful

27Views

0Replies

Blocking ARP packets on SG3428X-M2

I'm trying to block ARP packets from a specific IP range. I have tried seemingly every possible combination of ACL settings and none of them seem to affect ARP packets (0 packets matched when ethertyp

Switch ACL

By ekaszubski · Latest post Yesterday by ekaszubski

1Helpful

98Views

2Replies

Switch Frozen During Firmware Update

I use the Omada Controller F70B75 to manage my network. I tried to update the firmware of the above-mentioned switch to a new version (I think it was 1.20.x) and the switch is frozen. I tried power cy

Firmware UpdateTroubleshooting

By DocPMD

0Helpful

32Views

0Replies