Home

Forums

Stories

Knowledge Base

Business Community > All Threads > The remote server only supports an IP value, it does not allow to put a domain

< All Threads

The remote server only supports an IP value, it does not allow to put a domain

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

The remote server only supports an IP value, it does not allow to put a domain

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

SantyCR

2023-03-20 00:53:07 - last edited 2023-03-27 06:06:53

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2023-03-20

The remote server only supports an IP value, it does not allow to put a domain

2023-03-20 00:53:07 - last edited 2023-03-27 06:06:53

Tags: #VPN

Model: ER605 (TL-R605)

Hardware Version: V2

Firmware Version: 2.1.2 Build 20230210 Rel.62992

I am trying to create an OpenVPN client that accesses through a synology domain. But it only allows me to put the ip. In the help it indicates that the domain can also be used. What would be the correct way to enter that data?

thank you

1 Accepted Solution

Hank21

2023-03-24 10:02:50 - last edited 2023-03-27 06:06:53

Posts: 3673

Helpful: 726

Solutions: 497

Stories: 8

Registered: 2021-12-13

Re:The remote server only supports an IP value, it does not allow to put a domain-Solution

2023-03-24 10:02:50 - last edited 2023-03-27 06:06:53

Hello @SantyCR ，

Thanks for reporting this issue to the TP-Link community!

I'm afraid that ER605 doesn't support putting the Domain in the Remote Server at present, only the IP address is supported.

This has been already submitted as a feature optimized to the TP-Link team. And it will also be optimized in subsequent official versions of the ER605.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*

Recommended Solution

2 Reply

Virgo

LV5

2023-03-20 11:41:45

Posts: 2588

Helpful: 358

Solutions: 191

Stories: 0

Registered: 2021-05-10

Re:The remote server only supports an IP value, it does not allow to put a domain

2023-03-20 11:41:45

@SantyCR

Hi, Good question!

I have asked the same issue to their support, and the answer is it doesn't support to put a domain, only the IP works.

They told me that they have fed back this to senior engineer.

Just striving to develop myself while helping others.

Hank21

2023-03-24 10:02:50 - last edited 2023-03-27 06:06:53

Posts: 3673

Helpful: 726

Solutions: 497

Stories: 8

Registered: 2021-12-13

Re:The remote server only supports an IP value, it does not allow to put a domain-Solution

2023-03-24 10:02:50 - last edited 2023-03-27 06:06:53

Hello @SantyCR ，

Thanks for reporting this issue to the TP-Link community!

I'm afraid that ER605 doesn't support putting the Domain in the Remote Server at present, only the IP address is supported.

This has been already submitted as a feature optimized to the TP-Link team. And it will also be optimized in subsequent official versions of the ER605.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*

Information

Helpful: 0

Replies: 2

The remote server only supports an IP value, it does not allow to put a domain

The remote server only supports an IP value, it does not allow to put a domain

Information

Voters 0

Tags