connects 1G instead of 10G randomly Switch TL-SG3428X-M2 and Intel 10G 2P X-550-t adapter
Hello,
My PC having two Intel 10G 2P X-550-t adapter connects to TL-SG3428X-M2 (this model doesn't appear in the list above but I find TL-SG3428XPP-M2, I hope they are same) through ethernet cat 7 cables.
When I leave speed & duplex to auto negotiation it connects at 1G and a connection test through Intel PROset Adapter configuration utility indicates "Link speed: 1000Mbps. The link partner is not capable of higher speeds.".
However, when I put 10G full duplex manually, it connects "sometimes" at 10G but it is random and often the PC goes offline and then I cannot connect it unless I change the setting back to auto negotiation and the speed comes to 1G again.
The intel driver version is 4.1.254.0 dated 08/02/2024 and according to intel the problem is on the switch side.
Could you please help?
Thanks.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi @envirophile
Thanks for posting in our business forum.
It is not clear about your description. Let me try again.
Are you saying that you have a 10G RJ45 SFP module, and you are connecting a 10G NIC? They cannot negotiate to the 10Gbps link speed. Is that correct?
Because I don't see a way to connect a 2.5Gbps model to get a 10G speed. So, the assumption is that you have a 10G RJ45 module? That cannot work very well to get you linked?
- Copy Link
- Report Inappropriate Content
@Clive_A Thanks for your reply.
The router has 4 10G SFP modules to which I am connecting and not to the 2.5G ones.
- Copy Link
- Report Inappropriate Content
Hi @envirophile
Thanks for posting in our business forum.
envirophile wrote
@Clive_A Thanks for your reply.
The router has 4 10G SFP modules to which I am connecting and not to the 2.5G ones.
I was writing that if you were using SFP+ RJ45 to convert the SFP+ to Ethernet and connect it to your adapter. I was hoping to confirm we are on the same page.
So, that is to say, that I understand correctly that you are using the SFP+ RJ45 module on the switch and the router?
SFP+ module on the router you are connecting to, is that fiber-to-fiber or RJ45? What does it have to do with the 2-port X-550-T Intel adapter? Because Intel is an Ethernet adapter.
Because you should have a diagram Router_SFP+---SFP+_SWITCH_SFP+ > RJ45---Intel adapter. Which part of the connection is not working well?
- Copy Link
- Report Inappropriate Content
Thanks @Clive_A
yes, on the router I have a SFP+ to RJ45 adapter.
On the computer side I have Intel Ethernet 10 2P X-550-t adapter which has two 10G ethernet ports. I am using ethernet cat 7 cables to connect.
On both sides I have put jumbo packet 9000.
When I put auto negotiation on the computer ethernet card it connects at 1G speed. When I put 10G duplex, it doesn't connect.
- Copy Link
- Report Inappropriate Content
Hi @envirophile
Thanks for posting in our business forum.
envirophile wrote
Thanks @Clive_A
yes, on the router I have a SFP+ to RJ45 adapter.
On the computer side I have Intel Ethernet 10 2P X-550-t adapter which has two 10G ethernet ports. I am using ethernet cat 7 cables to connect.
On both sides I have put jumbo packet 9000.
When I put auto negotiation on the computer ethernet card it connects at 1G speed. When I put 10G duplex, it doesn't connect.
Let me confirm this. It seems that you refer the "router" to the switch SG3428X-M2. Is that correct? Because I am a little bit confused by your "router" thing.
Do you mean that you force the connection to 10Gbps, and it straightly fails to connect? If that's the case, it could be the cable issue. It does not work for 10Gbps and if you force that, that'll fail.
- Copy Link
- Report Inappropriate Content
@Clive_A yes it is the switch SG3428X-M2.It is a brand new cable installation.
- Copy Link
- Report Inappropriate Content
also, the cable test using intel adapter utility doesn't give any error.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 516
Replies: 7
Voters 0
No one has voted for it yet.