Home Network Community > All Threads > Router resets itself to factory default
< All Threads

Router resets itself to factory default

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Router resets itself to factory default

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Router resets itself to factory default
Router resets itself to factory default
2022-05-25 11:23:41
Model: Archer AX1500  
Hardware Version: V1
Firmware Version: Archer AX1500(US)_V1_220401

I was travelling last week when I noticed remotely that my home network was down. I could not connect remotely so when I got home I checked the modem and router and the router had reset itself to factory defaults. I connected via Ethernet and went through the setup process again, renaming and entering the password so all my devices could reconnect. This worked well for about 3 days, then it happened again. Went through setup again and in less than 48 hours it happened again. The only thing I can think of is there was a new firmware update dated 16 May 2022 which was during my travel. If the default firmware update setting is "Update Automatically" then I'm sure mine is set for that and it must have updated itself while I was gone. So my questions are: Is this a known issue and if so, is there a fix on the way? How can I fix this issue now and get it to stop resetting to factory default every couple of days? Thanks.

  0      
 
  0      
 
#1
Options
3 Reply
Re:Router resets itself to factory default
2022-05-26 02:13:05

Hello @twalls 

 

Apart from the firmware upgrade, were you aware of any other changes in the network or modem? Who is your ISP, and what is the model of the modem, please?

 

When you talk about reset, do you mean the router resets itself to factory defaults, and the wifi names are restored to default? 


To assist and figure it out efficiently, I've forwarded your case to the TP-Link support engineers who will contact you with your registered email address later. Please pay attention to your email box for follow-up. Thank you.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Router resets itself to factory default
2022-05-26 10:30:02

Thanks for replying  @Kevin_Z 

 

Sorry for not supplying enough detailed information. By factory default I meant it reset the SSID and all settings to factory defaults, as though this were a new router out of the box. When I log into the router it takes me through the initial setup process.

 

I was traveling when the problem first occurred so nothing had changed during that time. I have Comcast Internet and it is connected to a Motorola MB7420 cable modem, the same ISP and modem I've used since I bought the router in December 2019.

 

Thank you.

  1  
  1  
#3
Options
Re:Router resets itself to factory default
2022-05-26 11:19:04

@twalls 

 

Thank you very much for the detailed information. I have reported and forwarded the case to the support engineers, they will look into this and then suggest further. Please check your email box and respond.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  2  
  2  
#4
Options

Information

Helpful: 0

Views: 4143

Replies: 3

Related Articles
AX3000 Resets to factory default settings frequently
1175 1
Factory resets automatically?
471 0
WR940N factory resets itself
1462 2
Power off resets entire router to factory settings
1033 2
WR841N resets to factory settings
1023 1
Archer AX1500 (AX12) resets wifi settings to default
1290 2
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.