Home Network Community > All Threads > Deco M5 - Wired Connections Losing Network Access, Power Cycle Resolves Issue
< All Threads

Deco M5 - Wired Connections Losing Network Access, Power Cycle Resolves Issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco M5 - Wired Connections Losing Network Access, Power Cycle Resolves Issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Deco M5 - Wired Connections Losing Network Access, Power Cycle Resolves Issue
Deco M5 - Wired Connections Losing Network Access, Power Cycle Resolves Issue
2021-09-14 23:00:34 - last edited 2022-10-08 19:02:47
Model: Deco M5  
Hardware Version: V2
Firmware Version: 1.5.3 Build 20210203 Rel. 68223

Hello,

 

I've bought the Deco M5 (3-pack) back in AUG2019. This thing has been wonderful! One of the best IT purchases I've made in a long time!

 

However, for a few months now, about once every 1-2 weeks, my wired connections to the main Deco M5 router loses network. The wireless connections (devices and the other two pucks) usually continue to work without issue. A few cases this was not the case. I had this happen again today.

 

Performing an IP refresh does not resolve the issue (ipconfig /release && ipconfig /renew). Restarting the wired switch connected to it also does not resolve the issue. The only solution is to power cycle the main Deco M5 router.

 

I would naturally think the issue was the switch, however, a power cycle of the switch does nothing.

This switch is a Linksys switch setup in Bridge Mode and only forwards traffic from the Deco M5 to the wired devices.

  • DHCP is off on this switch.
  • Wireless is off on this Switch.
  • It even gets its IP from the Deco M5 router it is connected to.
  • The Deco M5 handles all DHCP Reservations.

 

Has anyone else seen anything like this?

 

My setup is connected as such:

  1      
 
  1      
 
#1
Options
1 Accepted Solution
Re:Deco M5 - Wired Connections Losing Network Access, Power Cycle Resolves Issue-Solution
2021-09-17 22:28:08 - last edited 2022-10-08 19:02:47
Hello, For the sake of argument, I purchased a TL-SG108E and have replaced the Linksys E4200 switch. I will be monitoring and will reply back if this happens again. Thank you for your prompt attention!
Recommended Solution
  1  
  1  
#7
Options
7 Reply
Re:Deco M5 - Wired Connections Losing Network Access, Power Cycle Resolves Issue
2021-09-15 00:57:54

@JohnMor 

Hi, thank you very much for your kind reply.

I might need to follow up on your case by email and could you please help me check the following information:

May I know the model number of the Linksys switch?

Could you please help me save a screenshot of the IP settings on the laptops?

And are you still able to ping the LAN IP of Deco as well as the Google DNS 8.8.8.8/8.8.4.4?

 

 

 

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us! Wi-Fi Schedule Ideas Wanted!
  0  
  0  
#2
Options
Re:Deco M5 - Wired Connections Losing Network Access, Power Cycle Resolves Issue
2021-09-15 05:58:30

@TP-Link 

Hello,

 

Here are your questions and answers:

  1. May I know the model number of the Linksys switch?
    • Linksys E4200 Switch
  2. Could you please help me save a screenshot of the IP settings on the laptops?
    1. Here is the IPConfig of my personal:

    • Ethernet adapter Ethernet:

         Connection-specific DNS Suffix  . :
   Description . . . . . . . . . . . : Killer E2500 Gigabit Ethernet Controller
   Physical Address. . . . . . . . . : 30-9C-23-17-B1-CF
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   Link-local IPv6 Address . . . . . : fe80::f93e:3b8b:d75b:f094%10(Preferred)
   IPv4 Address. . . . . . . . . . . : 192.168.68.111(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Tuesday, September 14, 2021 17:03:43
   Lease Expires . . . . . . . . . . : Wednesday, September 15, 2021 02:03:42
   Default Gateway . . . . . . . . . : fe80::9ada:c4ff:fe4c:fbc0%10
                                       192.168.68.1
   DHCP Server . . . . . . . . . . . : 192.168.68.1
   DHCPv6 IAID . . . . . . . . . . . : 221289507
   DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-24-E2-4E-60-30-9C-23-17-B1-CF
   DNS Servers . . . . . . . . . . . : 8.8.4.4
                                       8.8.8.8
  3. And are you still able to ping the LAN IP of Deco as well as the Google DNS 8.8.8.8/8.8.4.4?
    • When this happens, I have no IP assigned. Next time I'll try to hard code the IP and try again.
  0  
  0  
#3
Options
Re:Deco M5 - Wired Connections Losing Network Access, Power Cycle Resolves Issue
2021-09-16 06:45:54

@JohnMor 

Thanks a lot for the update.

I would like to forward your case to the senior engineers for further assistance.

Since the frequency of problems is relatively low but it does affect all the wired clients, it would be highly appreciated that you could give us a notification via email first,

Or mark down the exact time of the issue and save the system log before rebooting the main Deco.

 

Thank you again.

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us! Wi-Fi Schedule Ideas Wanted!
  0  
  0  
#4
Options
Re:Deco M5 - Wired Connections Losing Network Access, Power Cycle Resolves Issue
2021-09-16 13:21:04
How do you save the system log? I assume that the log gets overwritten between power cycles?
  0  
  0  
#5
Options
Re:Deco M5 - Wired Connections Losing Network Access, Power Cycle Resolves Issue
2021-09-17 01:27:51

@JohnMor 

Hi, you could save logs from the web UI, and yes, it would be overwritten after reboot so it needs to be saved before the reboot.

And I have seen that you have emailed us some logs already.

Thank you very much.

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us! Wi-Fi Schedule Ideas Wanted!
  0  
  0  
#6
Options
Re:Deco M5 - Wired Connections Losing Network Access, Power Cycle Resolves Issue-Solution
2021-09-17 22:28:08 - last edited 2022-10-08 19:02:47
Hello, For the sake of argument, I purchased a TL-SG108E and have replaced the Linksys E4200 switch. I will be monitoring and will reply back if this happens again. Thank you for your prompt attention!
Recommended Solution
  1  
  1  
#7
Options
Re:Deco M5 - Wired Connections Losing Network Access, Power Cycle Resolves Issue
2021-09-22 03:14:53

@JohnMor 

Thank you and please feel free to update the email if you have any further findings.

 

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us! Wi-Fi Schedule Ideas Wanted!
  0  
  0  
#8
Options

Information

Helpful: 1

Views: 922

Replies: 7

Related Articles
Connecting Xbox to Deco M5 wired?
2069 0
Wired Connections
461 0
How to wired connect printer to Deco M5.
793 0
M5 network fast. Wired PC's slow now?
580 0
Deco M5 not assigning IP to wired devices, previously did.
1736 0
AC4000 PPoE issues - losing wired network.
508 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.