TL-WR841N transmit power

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TL-WR841N transmit power

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TL-WR841N transmit power
TL-WR841N transmit power
2021-01-23 21:58:08
Model: TL-WR841N  
Hardware Version: V14
Firmware Version:

 What is the maximum transmit power with out the < or > signs? The manual says low medium or high.

  0      
  0      
#1
Options
6 Reply
Re:TL-WR841N transmit power
2021-01-25 13:05:27
It would be the max allowed by the country for each frequency. In the US it would be controlled by the FFC max. See https://www.air802.com/fcc-rules-and-regulations.html
  1  
  1  
#2
Options
Re:TL-WR841N transmit power
2021-01-25 22:12:18

@MiniMike 

 

Max transmit power is 20 dBm.

  0  
  0  
#3
Options
Re:TL-WR841N transmit power
2021-01-25 22:34:08
Archer: Thanks for your reply. Here is what I am trying to achieve: I have a vacation house on a lake and across the lake someone has Xfinity with the public hotspot turned on. I have Xfinity access at home so I can legally connect to the internet with my password using that signal. I am connecting to it now with a 2.4 21DB dish and a ordinary Wifi card in my desktop. The signal fades in and out and it is worse when leaves are on the trees. I want to provide access to my guests as well using their laptops Plus I need a little more power. Every time I post something on a forum I get attacked and told what I have working won't work and what I want to do is illegal. I don't understand the hostility for asking a question. I understand that I need a WISP mode router. For simplicity sake I only want a little more power, 2.4 and not dual band. 1000mw max if possible. I can always dial it back. This is in the mountains and not in the suburbs or city. I see on the tp link site https://www.tp-link.com/us/user-guides/tl-wr841n_v14/chapter-2-connect-to-the-internet#ug-sub-title-2 shows the configuration I am looking for except I want to use my dish with a short coax for one antenna. And maybe run a ethernet cable to my desktop. I have a version 9 TL-WR841N which does not support WISP. I was thinking of getting one with a higher version but I am unsure of the transmit power. I cannot grasp the descriptions of WISP vs repeater vs relay vs signal booster and they vary from site to site. Therefore I am asking for advice about which router and how to achieve what I want. If you are interested I can tell you about the TV antenna I built that receives a picture from 50 miles away over a thousand foot mountain using info from a forum. Mikey
  0  
  0  
#4
Options
Re:TL-WR841N transmit power
2021-01-25 22:54:37
Most routers will transmit at max or have an option to adjust the power. None will or should exceed the FCC max in the US as that can cause issues.
  0  
  0  
#5
Options
Re:TL-WR841N transmit power
2021-01-26 13:03:24
I suggest you try a router with beamforming such as the AX11000. A Wisp or extender will not do you much good unless it can be placed where you can get a good signal to and from the router and your devices.
  0  
  0  
#6
Options
Re:TL-WR841N transmit power
2021-01-31 13:19:05

@MiniMike 

 

A few other thoughts.

 

Consider contacting Xfinity to see if they have a special program as I am sure others have the same problem. Such as:

 

- A special price for a vacation home for existing users.

 

- Set up Xfinity in your lake home and you can switch between both based on where you are (they advertise that you can switch their service online in five minutes).

 

- That they add a Xfinity hot spot nearby (might help if several of your neighbors have the same issue).

 

- Offer to host a hot spot (you supply the place and power and they the equipment and service),

 

Post on the Xfinity forum as there may be other with the same issue.

 

 

 

 

  0  
  0  
#7
Options

Information

Helpful: 0

Views: 1913

Replies: 6

Related Articles