Home

Forums

Stories

Knowledge Base

Home Network Community > Powerline Adapters > TL-WPA7510 V1 Will not enter Pairing Mode

< Powerline Adapters

TL-WPA7510 V1 Will not enter Pairing Mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TL-WPA7510 V1 Will not enter Pairing Mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

RangerZ

2022-01-22 00:01:29

Posts: 8

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2022-01-21

TL-WPA7510 V1 Will not enter Pairing Mode

2022-01-22 00:01:29

Model: TL-WPA7510 KIT

Hardware Version: V1

Firmware Version: Unkown

I am trying to get a TL-WPA7510Kit (WPA7510 V1 and PA7010 V2) configured. I have used other TP-link power line adapters and familair with the process.

I am unable to put the WPA7510 into pairing mode. The Powerline and Ethernet LEDs are off. Pressing the PAIR button does not start the Power LED flashing. I have reset the device multiple times. The unit is not seen in the tlPLC utility. The WIFI is broadcasting and I can connect at the default SSID, but I can not connect to the devices web server at http://tplinkplc.net I tried to connect the WPA7510 with the LAN cable to the router, but it is not recognized and I do not get access to the internet when connected to the devices WIFI.

The PA7010 is recongnized by the tlPLC utility. It does flash when the PAIR button is pressed and I ssupect is working as it should, though may not be on the latest FW. I have tried loading the latest FW for the dives (V@) but it fails to load (I get a lillte frowning face). Not sure I care ATM. I do not think this is my issue.

Any one have any thoughs or suggestions?

3 Reply

RangerZ

LV1

2022-01-22 18:01:07

Posts: 8

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2022-01-21

Re:TL-WPA7510 V1 Will not enter Pairing Mode

2022-01-22 18:01:07

Today I was able to connect to the devices web server. It appears to be on the latest Firmware.

I did notice that in the section Device Settings => Powerline that both the MAC address and Powerline Key display no conent (blank).

Solla-topee

2022-01-24 09:29:14 - last edited 2022-01-24 09:31:56

Posts: 13125

Helpful: 2248

Solutions: 1829

Stories: 8

Registered: 2020-05-19

Re:TL-WPA7510 V1 Will not enter Pairing Mode

2022-01-24 09:29:14 - last edited 2022-01-24 09:31:56

Hello @RangerZ

1. Please try a factory reset on Wi-Fi powerline unit TL-WPA7510
via the RESET button/ RESET hole
With device powered on, press and hold the Reset button (or use a pin to press reset hole) until all LEDs will turn off and start on again.

Please check if the Powerline will be flashing after you press the Pair button?

Put 2 powerline unit in the wall sockets, in the same room, and pair them again :

Paring Note: press Pair button only for 1 sec, Power Leds should be flashing on both powerline units in pairing process. ( if the Power Led does not blink, press it for 1 sec again)
FAQ258: How to secure (pair) the Powerline Network?

2. If you are able login web page of it, you could also try another factory reset from System Tools-> backup and restore-> factory restore

And try check if TL-WPA7510 <WiFi>Laptop installed tpPLC utility, could it be detected by tpPLC utility?

May I know was there any firmware update failure on this powerline unit?

>>Landscape Mode - Tapo App for Pad. >>Smart Action 2.0 Explore and meet the next level home automation. >>How to position my TP-Link camera for optimal performance.

RangerZ

LV1

2022-01-25 21:50:17

Posts: 8

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2022-01-21

Re:TL-WPA7510 V1 Will not enter Pairing Mode

2022-01-25 21:50:17

@RangerZ

It's worth noting that:
1 - The TL-WPA7510 will not enter pairing mode. The light remains solid no matter what manner I press the PAIR button
2 - In the TL-WPA7510's web browser (TPLINKPLC.NET) Device Settings => Powerline, the MAC Address and Powerline Key from the device are missing. I would think, but don't know for sure, that this would display the relevant values located on the back of the device.

I have performed multiple resets from the button with no success. I do not get ALL the lights to turn on. The Power LED comes on, followed by the 2 radio LEDs. The Ethernet and Powerline lights do not iluminate at any time, even with a cable connected.

As noted, pressing the PAIR button does not display the Power (or any other LED) to flash.

I have looged in to the TL-WPA7510 and performed a factory restore with change in the situation.

The device is on the latest firmware, but I am succesfullly able to re-apply the firmware (1.0.4. Build 20181226 Rel.39907). No error message on flashing.

I also have tried to manual "Add a new device" with the devices Powerline Key vaule as well as the accompanying TL-PA7010's Powerline key. The process returns a "Device not added" message along with a red frown face.

TL-WPA7510 V1 Will not enter Pairing Mode

TL-WPA7510 V1 Will not enter Pairing Mode

Information

Voters 0

Tags