Deco Forums - Home Network Community

Deco IoT network not working/no internet

I have a mix of deco units (10 total). There are (3) XE5300, (3) X3600, (3) M9 plus and (1) X-50 outdoor unit. These units are also mostly hardwired for ethernet backhaul to unmanged network switches

Access Point ModeBackhaul MethodVLAN/IPTVFeature RequestIoT

By R3adyPlay3rOn3 · Latest post Sunday by jzchen

0Helpful

67Views

1Replies

Make Deco Disable DHCP Server When Upstream DHCP Available

Hello, I have a Deco W3600 that I am using to act as a wireless bridge between my primary router and downstream devices. I am, however, faced with an issue: if the power goes out, then the Deco will b

Feature RequestAccess Point Mode

By JacobBridges

0Helpful

56Views

0Replies

Cannot set up Chromecast to X60 network

Today suddenly my Chromecasts that were previously working via my X60 mesh network could not be connected to. I tried factory resetting them, and now I am having trouble setting them up again. During

Access Point ModeGoogle Assistant

By BobMullNH · Latest post 3 weeks ago by BobMullNH

1Helpful

124Views

2Replies

X50 drops or limits connection speed for no reason

Hi, I have an issue: I changed ISP provider for an "upgraded" 100MB/s 5G FWA (I live in a sub-sub-suburban area where fiber is not available). Here is the current setup : ISP ROUTER (TOZED ZLT 51) ---

Access Point Mode

By TL176

1Helpful

73Views

0Replies

Linking two X50 Outdoor units

I want to link two of the X50 Outdoor units together. The first is inside the house connected to a T-Mobil 5G Whole Home Gateway with an ethernet cable. I want to add a second unit outside of the hous

Access Point Mode

By Bob1313

0Helpful

83Views

0Replies

Disconnections and latency variation when using Deco

Hello, I just set the Decos up this morning, and since then I am experiencing disconnection periods, and some latency variations. Those problems even occur when I'm connected to my ISP router, as long

Access Point Mode

By Zaltori · Latest post 2025-03-04 19:13:33 by Zaltori

3Helpful

186Views

3Replies

Setting up DECO in Access Point mode with an existing Modem/Router combo

MODEL: WE10800 What do I need to do to my existing modem/router when setting up DECO as an Access Point? I have one (the main Deco) connected to the modem/router via ethernet cord. The others (3 more)

Access Point Mode

By Vito895 · Latest post 2025-02-28 02:24:34 by EricBWA

0Helpful

182Views

2Replies

Deco and Festa Combination

Hello, I just bought a Deco BE11000 (3-pack), Deco BE10000 (BE63) - 2-pack and 3 Festa FS308G Ethernet switches. They're arriving tomorrow and I'll be installing them the next day. I know that I can u

Wi-Fi 7Access Point Mode

By aldera

0Helpful

129Views

0Replies

Non-main nodes (hardwired & wifi) blinking red after IP Passthrough on main/router

Hello. I recently did a passthrough IP on the main ISP router to which the main Deco is hardwired to, including disabling ISP router's wifis, disabling firewall etc, Fixed DHCPS etc. This caused the i

Feature RequestBackhaul MethodAccess Point ModeWi-Fi 6E

By coss80

0Helpful

96Views

0Replies

Deco in AP mode doesn’t connect to ethernet

Hi, I have 3 x60 decos and a router. The main deco is connected to the router via Ethernet cable and is configured as an Access Point. It works great. The problem is with the 2 satellites: - Sat 1 is

Access Point Mode

By Ananya_deco · Latest post 2025-02-09 10:56:30 by Ananya_deco

0Helpful

195Views

2Replies