C325WB keeps losing WiFi
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
I purchased the C325WB to work alongside my other Tapo cameras a few weeks ago. Strangely, it was a V1 hardware edition. Sadly, this camera has never maintained its WiFi connection, despite being in clear line of site to a Deco X75 mesh AP just 5 metres away.
- The firmware is up-to-date.
- WiFi is optimised (according to Deco app) with no overlap with neighbour channels when using a PC based WiFi analyser.
- The entire WiFi stack is TP-Link based, with 2x X75 mesh APs connected to an AXE5400 router.
- Signal testing at the camera location results in a strong connection.
- Any other device placed in the location of the camera receives strong WiFi.
- Sadly, I cannot test using ethernet outside.
- Rebooting the camera in position does not force its reconnection to WiFi
- Rebooting the mesh AP the camera connects to does not force its reconnection to WiFi.
I am at a loss as to why this happens. My other TP-Link cameras do not experience this issue, even when placed in the same location as the C325WB as a test.
Any and all help appreciated.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi,
You can try to turn off the Fast Roaming feature on the Deco app and check if the Tapo C325WB will work fine. If the guest network on the Deco is not enabled, you can also enable the 2.4G guest network, reset and reconfigure the Tapo C325WB to connect to the guest network, and then check if it will work fine.
If the problem remains, please check the LED status on the camera when it shows offline on the Tapo app, and please help check the Wi-Fi signal value on the camera's Device Settings>Device Info page.
Best Regards
- Copy Link
- Report Inappropriate Content
Thank you for your reply. Very much appreciated!
I can confirm that Fast roaming is disabled (always has been) and that when connected, the signal is displayed as strong. When the camera loses WiFi, the status led is red, with a slow blink which indicates it is trying to connect. The camera behaves the same when connected to the guest or IoT networks.
Many thanks once again.
-Nick
- Copy Link
- Report Inappropriate Content
Hi,
I have reported the issue to the tech team, and they will likely reach out to you via email to continue troubleshooting your issue. Please check your email box and confirm.
Best Regards
- Copy Link
- Report Inappropriate Content
I have the same issue, also have Deco Mesh.
The cameras are on a 5GHz/2.4GHz dual band mesh with fast roaming disabled.
I can live view the camera fine, as soon as it starts recording it reports poor network quality.
Mesh AP is at the other side of the wall to the camera. My older Kasa cameras had no issue at all. 300mbps Internet connection and Tapo camera reports good network connection
- Copy Link
- Report Inappropriate Content
Hi,
Do you see the 'poor network quality' message when you press the record button on the camera's Live View page to record video manually, or when the camera detects events and starts to record video automatically?
Have you inserted an SD card into the camera to store video recordings?
What's the Wi-Fi signal value on the camera's Device Settings>Device Info page?
How about the LED status on the camera when the app reports 'poor network quality'?
Best Regards
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi,
The phenomenon seems related to the network quality rather than the camera losing the Wi-Fi connection. Please check if the camera can connect to the router/deco by an ethernet cable or if you can make them closer, and then check if the camera will work well. Or you can select a low video quality or select Auto on the camera's Live View page, then check if the "poor network quality" message will disappear when the camera detects events.
Best Regards
- Copy Link
- Report Inappropriate Content
Are you using the original power plug & cable? Or is it extended with wire extension?
- Copy Link
- Report Inappropriate Content
I am using the original plug and attempting to use WiFi. However until that is resolved, I'm using ethernet because I need the camera working.
- Copy Link
- Report Inappropriate Content
@N_Gatt oh, so it works fine with ethernet? hmmm
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 1186
Replies: 10
Voters 1
