HS100 needs power recycle to reconnect to resarted wifi router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

HS100 needs power recycle to reconnect to resarted wifi router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
HS100 needs power recycle to reconnect to resarted wifi router
HS100 needs power recycle to reconnect to resarted wifi router
2020-01-03 12:04:57 - last edited 2020-02-28 06:47:52
Model: HS100  
Hardware Version: V2
Firmware Version: 1.5.8

I have two HS100 plugs.  When I need to restart my wifi router they both fail to reconnect to wifi without a power off / on.  Router is Buffalo WZR-600DHP2 using Firmware: DD-WRT v3.0-r40559 std (08/06/19).  The plugs fail to connect (orange light) and can't be 'seen'  by google home or kasa app.  They connect via the 2.4 ghz AP.  A 5 ghz AP exists with a different SSID.   I have a single WEMO device which does not exhibit the same behaviour.

 

Any ideas?

  0      
  0      
#1
Options
1 Accepted Solution
Re:HS100 needs power recycle to reconnect to resarted wifi router-Solution
2020-01-13 16:18:38 - last edited 2020-02-28 06:47:52
I should have mentioned this issue was after a router firmware upgrade. I think the issue was related to the new defaults for wifi channel and protocol selections. I experienced other issues and reverted to an earlier build which proved stable before the upgrade. This issue has now gone away.
Recommended Solution
  0  
  0  
#4
Options
6 Reply
Re:HS100 needs power recycle to reconnect to resarted wifi router
2020-01-08 06:06:48

@thevilla 

 

Hello, what is the led status of the two HS100 after the main router booted up? 

 

How do you make them reconnect to the home network? 

 

Try to move them closer to the main router and you can reserve an IP address for each plug on the web UI of the main router to give it a go. 

 

May it help. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:HS100 needs power recycle to reconnect to resarted wifi router
2020-01-09 11:32:34 - last edited 2020-01-09 12:31:49

Hi, Thanks for the reply. LED lights : Wifi is amber. Power light is off. The sockets reconnect if I power each one off and on again. I have tried moving within 1 meter of the router and assigning static IP addresses. The behaviour is not improved by the changes.

When the issue occurs, the router is rebooted so wifi is not available.  The plugs flash green wifi lights until the wifi is available again after the router reboot.  The plug's wifi light then turns solid amber - at the same time all other wifi clients (various vendors) connect successfully.  The HS100 plugs do not connect until their power is cycled at the wall socket.

  0  
  0  
#3
Options
Re:HS100 needs power recycle to reconnect to resarted wifi router-Solution
2020-01-13 16:18:38 - last edited 2020-02-28 06:47:52
I should have mentioned this issue was after a router firmware upgrade. I think the issue was related to the new defaults for wifi channel and protocol selections. I experienced other issues and reverted to an earlier build which proved stable before the upgrade. This issue has now gone away.
Recommended Solution
  0  
  0  
#4
Options
Re:HS100 needs power recycle to reconnect to resarted wifi router
2020-02-28 01:14:29

@thevilla I am having the exact same problem.  My router is an ASUS RT-AC3200 flashed with DD-WRT v3.0-r40559 std (08/06/19).  I have an IOT VLAN (which is on a virtual wireless network), and if I reboot the router, all other devices on that network reconnect (google home, chromecast etc), except my 5 TPLink smart switches (HS100 and HS110 models).  They try to reconnect, then just stay "orange" like you described.  The only way to fix them is to walk around the house and power cycle them all.

 

What firmware version did you fall back to to fix the issue?

  0  
  0  
#5
Options
Re:HS100 needs power recycle to reconnect to resarted wifi router
2020-03-09 11:50:06 - last edited 2020-03-13 06:31:42

As a followup to my previous post, I tried downgrading DDWRT to firmware version DD-WRT v3.0-r36527 std (08/09/18) and the issue was resolved.  Thought this might be useful for anyone else with TPLink HS100 switches and DDWRT firmware on their router.

  0  
  0  
#6
Options
Re:HS100 needs power recycle to reconnect to resarted wifi router
2020-06-30 04:37:13

@thevilla try setting a static address for the smart plug on your wifi router. Look under DHCP Server (or similar) in the settings. 

 

Doing that appears to have fixed my HS110 losing the connection.

  0  
  0  
#7
Options

Information

Helpful: 0

Views: 1744

Replies: 6

Related Articles