Smart Action: T310/T315 Temperature or Humidity Automation Doesn't Take Effect

Smart Action: T310/T315 Temperature or Humidity Automation Doesn't Take Effect

Smart Action: T310/T315 Temperature or Humidity Automation Doesn't Take Effect
Smart Action: T310/T315 Temperature or Humidity Automation Doesn't Take Effect
2023-07-07 13:09:36 - last edited 2024-05-15 09:34:20

05/15/2024 Update Delete solutions for the special cases where the automation does not take effect immediately if T310/T315's current value has already reached the set threshold or range when creating the automation. 

 

This Article Applies to:

Tapo T310
Tapo T315

 

 

Issue Description/Phenomenon:

 

If you are experiencing issues with the automation created using Tapo T310/T315 and it is not functioning as expected, please check if you fall into one of the following situations.

 

To ensure a proper understanding of the activation logic employed in Tapo Automation for the Temperature and Humidity sensor, it is essential to take note of the following:

If you are utilizing temperature or humidity changes from the Tapo T310/T315 sensor as a trigger for your automation, please make sure that the changed value must cross the set threshold to activate the automation as intended. If the value is equal to the threshold or the changed behavior does not match the set Trigger condition (e.g., "Over" or “Below"), the automation will not be activated.

 

 

For example:

Creating an Automation using Tapo T310 as the Trigger device: When T310 temperature over 20℃.

 

Changes Automation Activated? Note

When creating/saving the automation

(Current temperature 25℃)

Yes

When saving settings, the Tapo App verifies the current temperature/humidity data against the automation settings.

 

If the current values meet the trigger conditions, a pop-up window will prompt you to either execute the action immediately or skip it.

Rise from 18℃ to 22℃

Rise from 20℃ to 21℃

Yes /
Rise from 18℃ to 20℃ No The changed value (20℃) equals the set threshold, it does not cross over 20℃.
Rise from 21℃ to 25℃ No

Not the set behavior: Temperature (cross) over 20℃. No temperature crossing behavior occurs.

 

Drops from 25℃ to 19℃ No Not the set behavior: Temperature (cross) over 20℃.

 

 

Troubleshooting Tips

1. Ensure device firmware, Tapo hub, and Tapo APP are updated. 

2. Check if the automation rule is set correctly. (Trigger and Action device, trigger value, Over/Below, Effective time, etc)

3. Check if the detected value is updated in time in the APP or on the screen (For T315 only).

4. Check the signal strength on both Tapo sensor and the hub. Adjust device's location if the signal is weak.

  • For the Tapo sensor and H100: go to device's settings page ->Device's Info -> Click the signal icon to show the RSSI rate.
  • For the Tapo H200: go to device's settings page ->Network Connection -> Click the signal icon to show the RSSI rate.
  • Switch H200 to ethernet connection if it was wirelessly connected.

 

  • Strong: more than -50 dBm
  • Good to Average: among -70 dBm to-50 dBm
  • Poor: less than -70 dBm  (Too weak!)

 

 

Connection Diagram of Tapo SubG Devices in the Network 

Landscape Mode - Tapo App for PadShare Your Pet Story. Win Free Tapo Care!Smart Action 2.0 Explore and meet the next level home automation.
  0      
  0      
#1
Options
16 Reply
Re:Smart Action: T310/T315 Temperature or Humidity Automation Doesn't Take Effect
2023-10-20 17:09:30

  @Wayne-TP 

Hello,
temperature automation is completely useless in this case. 
If I want to control the heating, the temperature in the room is e.g. 18°C, switching on the P100 is below 19°C and switching it off is above 20°C, the automation will not start. 

The shortcuts I use to set the automation are also useless. I had the idea of setting a heating shortcut for a standard week, a shortcut for still 21°C and a shortcut for still 19°C. When switching these shortcuts nothing happens, no automation takes place. 

Also setting up automations is very complicated and unusable. You like to flaunt the name smart, but there are no smart functions. A regular wireless thermostat is much simpler and most importantly works.
Another thing that is sorely lacking is the ability to set the automation ALL triggers will activate the automation. It doesn't even solve the effective time. Example: I want the P100 to trigger if the door is closed and the motion sensor is active. This simply cannot be done. Any trigger in the group will turn on this automation. 

One last thing I have on this topic. How is it possible that the automation setting for temperature can only be adjusted by 1°C? Are we really in the 21st century? I would expect such a possibility in a mechanical thermostat and not in a digital sensor that sends the temperature to 1 decimal place.

Tapo has pretty well done cameras, lights, LED strips. It's a little worse with the switches, which sometimes don't respond, don't turn on the lights, or there is a delay. As far as motion sensors, open doors, unfortunately I don't see the use until automation ALL triggers will activate.

Pavel

  14  
  14  
#2
Options
Re:Smart Action: T310/T315 Temperature or Humidity Automation Doesn't Take Effect
2023-10-25 10:17:41

  @PavelV 

 

I 100% agree with the above post! I have invested in 2 Tapo smart sensors T310 and 10 smart plugs T115, 1 smart hub H100 and a C220 camera. Despite the fact that the camera and plugs themselves are of good quality, the so-called smart automation with the sensors is absolutely unusable! I have an office space with electric heating. If this room is used in the winter, I want this heating to be able to be turned on and off remotely (e.g. an hour in advance), and to only heat between a minimum and maximum temperature that I set myself. I've tried everything but this simply doesn't work!! Would love your feedback!

  8  
  8  
#3
Options
Re:Smart Action: T310/T315 Temperature or Humidity Automation Doesn't Take Effect
2024-01-10 18:54:50

Sorry for "necroing" this thread, but has any progress been made into actually making automation usable for temperature control?

I'm trying to set up a wi-fi power socket to turn on a heater when below certain temperatures, but also within certain times of day and it flat out doesn't work if the temperature is below the set range when that time of day comes.


Does anyone know of an alternate app that can be used to ... you know, perform a check every minute and turn on a heater if the temp is low or something? Simple stuff like that?

  3  
  3  
#4
Options
Re:Smart Action: T310/T315 Temperature or Humidity Automation Doesn't Take Effect
2024-01-18 04:32:44

  @Wayne-TP We are having a similar problem. In our case the p115 is turning an extractor on to lower the temperature, but not turning off again, reducing the temperature too far.

  3  
  3  
#5
Options
Re:Smart Action: T310/T315 Temperature or Humidity Automation Doesn't Take Effect
2024-03-23 10:51:40

  @Wayne-TP 

 

Just adding my voice here to say that temperature automations simply do not work for me despite trying all the troubleshooting suggestions.

  3  
  3  
#6
Options
Re:Smart Action: T310/T315 Temperature or Humidity Automation Doesn't Take Effect
2024-03-25 07:56:48

  @homerjam 

 

You may share more details by starting a new post Start a New Thread, such as device's info, smart action configurations, things you have tried, etc. Our team and other experience users would be happy to provide our suggestions. 

Landscape Mode - Tapo App for PadShare Your Pet Story. Win Free Tapo Care!Smart Action 2.0 Explore and meet the next level home automation.
  1  
  1  
#7
Options
Re:Smart Action: T310/T315 Temperature or Humidity Automation Doesn't Take Effect
2024-03-25 17:00:29

  @Wayne-TP how about doing some tests yourselves simulating imperfect conditions, wifi dropouts etc. I have a T315 and a couple of smart plugs, latest app/firmware, I have an automation which turns on the plugs at 7am and another to turn off at 10pm. Within in this time window I also have an automation that turns off the plugs at 22 degrees and another that turns on the plugs below 20 degrees. This is the absolute basic use case for these sensors - replacing a traditional thermostat. Surely the number of complaints and people with the same issue are enough to warrant some investment in your apparently defective products?

  1  
  1  
#8
Options
Re:Smart Action: T310/T315 Temperature or Humidity Automation Doesn't Take Effect
2024-03-27 06:08:11

  @homerjam 

 

Tapo Smart Action is a cloud-based feature. Disconnection of the internet or WiFi will cause automation to malfunction.

Landscape Mode - Tapo App for PadShare Your Pet Story. Win Free Tapo Care!Smart Action 2.0 Explore and meet the next level home automation.
  0  
  0  
#9
Options
Re:Smart Action: T310/T315 Temperature or Humidity Automation Doesn't Take Effect
2024-03-27 11:22:51

  @Wayne-TP 

So what is the purpose of the hub?

Why isn't this requirement in BOLD LETTERS ON THE BOX?

Why is there no reconnection logic to mitigate against temporary dropouts?

Why is there no "reset" button in the app?

Why are there no logs or shareable configuration available?

Why are you skimping on QA and passing the buck to your consumers?

  4  
  4  
#10
Options
Re:Smart Action: T310/T315 Temperature or Humidity Automation Doesn't Take Effect
2024-10-09 17:14:13

  @Wayne-TP I have the same problem with the combination of the Tapo T310 Temperature and Humidity senzor with P115 socket - it just doesn't function properly.

 

When I enter teh contidtions, it asks me to do I want to execute the automation now, and if those conditions are being met, it is not executing the automation automatically. Looks like some coding woudl need to be done to fix this issue.

  1  
  1  
#11
Options