EAP670 not use Full bandwidth 2,400MB After Update firmware 1.0.6
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.EAP670 not use Full bandwidth 2,400MB After Update firmware 1.0.6
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
i have EAP 670 V1 9 Device + Omada OC200 i use EAP 670 Fix only width160Mhz FW 1.0.3 in mode standalone & mode Adopt member in omeda in 2 mode every Wifi6 device & NB wifi6 client can connect EAP670 Full bandwidth 2,400MB but after update new firmware 1.0.6 every device & client why connect EAP670 in bandwidth 1,200MB can not connect Full bandwidth 2,400MB not same befor update i need how to resulve this issue
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
You can try optimizing wireless network by changing different channel, channel width, Tx Power.
Try set a 6G WiFi to test.
- Copy Link
- Report Inappropriate Content
read up on real time air speeds and negotiated air time speeds. Then you will kinda u der stand what's going on here.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
you reboot the eap or change the location of your device, the signal source can change.
your speed then can vary. get a clear understanding of link speed. usually, a failure to max link speed is about the distance and eap channel width.
(by default, eap channel width is on auto. you set it to 160mhz, any device don't support this 160mhz will lose connection and signal after the change)
- Copy Link
- Report Inappropriate Content
@Tedd404 I have 9 points of EAP670. When installing, use default firmware 1.0.3, use BW 2,400mb, every client has no problem. But there was a problem after Firmware Update 1.0.6
- Copy Link
- Report Inappropriate Content
i mean do you do test alone to narrow down the problem to the firmware?
i would not argue there were bugs. even windows and ios make serious bugs in 2023.
so, what makes you draw the conclusion to the firmware prevents you from getting a 2400Mbps wireless speed? like I said, 2400mbps only exists to 160mhz as channel width. search it online if you think I am fooling around.
- Copy Link
- Report Inappropriate Content
Also, just because Windows shows the link speed as 2.4Gbps vs 1.2Gbps, does not mean the device will come close to 2.4Gbps of throughout in a real-world data transfer scenario. In order to achieve that data transfer rate, all devices would need a link speed of at least 2.4Gbps, and all devices involved in the data transfer would need to be physically very close to the EAP to achieve that speed internally on your Wifi network.
- Copy Link
- Report Inappropriate Content
@Tedd404 before i use FW 1.0.3 in mode standalone & join in omada not probleme every device is a Intel(R) Wi-Fi 6E AX211 160MHz can use full bw 2,400MB but after update new FW 1.0.6 have this probleme every device drop 1,200MB i test FW 1.0.6 in standalone same issue omeda
- Copy Link
- Report Inappropriate Content
@Shoresy Network Switch i use TL-SX3206HPP 10GB POE & TL-SG3210XHP-M2 2.5GB POE installation complete i use FW 1.0.3 in mode standalone & join in omada not probleme every device is a Intel(R) Wi-Fi 6E AX211 160MHz can use full bw 2,400MB but after update new FW 1.0.6 have this probleme every device drop 1,200MB i test FW 1.0.6 in standalone same issue omeda
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 2020
Replies: 11
Voters 0
No one has voted for it yet.