Business Community > Controllers > TL-R605 not visible in Dashboard and Speedtest loop
< Controllers

TL-R605 not visible in Dashboard and Speedtest loop

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
1456

TL-R605 not visible in Dashboard and Speedtest loop

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
56 Reply
Re:TL-R605 not visible in Dashboard and Speedtest loop
2021-02-18 03:34:44

Dear @Munnik,

 

The new version 4.2.11 displays the gateway now. I tested this yesterday.
But this morning It was not there anymore. I had to do a manual speed test again to see the gateway again.
It did not remember the gateway. Is there a setting for this? How frequent will the controller perform a speed test on it's own?

 

 

When you say that the gateway was not there anymore, do you mean that the Gateway show as N/A like the below picture showing?

 

For the Speed Test frequency, you may enable Periodic Speed Test to set the interval.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  1  
  1  
#43
Options
Re:TL-R605 not visible in Dashboard and Speedtest loop
2021-02-18 09:34:43

@Fae 

 

Yes, shown as "N/A".

 

  0  
  0  
#44
Options
Re:TL-R605 not visible in Dashboard and Speedtest loop
2021-03-11 13:44:46

@Fae 

I also have same issue.

Just completed installing my new gateway and switch last night to go with OC200 and APs. 

Capacity / gateway was there after doing the speed test (which does loop a few times) - and then disappears.


 

TL-R605 1.0.1 Build 20210113 Rel.35074

TL-SG2008P 1.0.0 Build 20200608 Rel.76470

OC200 4.2.11

2x EAP-225 5.0.0 Build 20200918 Rel. 58628

1x EAP-225 Outdoor 5.0.0 Build 20201015 Rel. 54720

 

 

  1  
  1  
#45
Options
Re:TL-R605 not visible in Dashboard and Speedtest loop
2021-03-25 02:56:17

Dear @EIBROG, 

 

I also have same issue.
Just completed installing my new gateway and switch last night to go with OC200 and APs. 
Capacity / gateway was there after doing the speed test (which does loop a few times) - and then disappears.

 

 

When we click "speed test" on the gateway to test the speed in Dashboard, what we see is just a simple loop animation, it doesn't mean the real process of speedtest.

 

As for the disappeared Capacity/Gateway value, if you enable Periodic Speed Test (mentioned above), does it make any difference?

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  1  
  1  
#46
Options
Re:TL-R605 not visible in Dashboard and Speedtest loop
2021-03-27 01:49:30

@Fae Apologies - didn't notice that! I have enabled that now and will see if it maintains Utilization.

 

  0  
  0  
#47
Options
Re:TL-R605 not visible in Dashboard and Speedtest loop
2021-04-07 05:02:50 - last edited 2021-04-07 05:03:52

I have the same issue described here and I have all the software on the latest version possible.

The gateway info is always "N/A" and the speedtest always gives me an error. (even with the periodic test enabled)

 

 

TL-R605v1 | 1.0.1 Build 20210113 Rel.35074

TL-SG2008Pv1 | 1.0.0 Build 20200608 Rel.76470

OC200v1 | version 4.2.11 | 1.7.4 Build 20210118 Rel.72627

2x EAP-225v3 | 5.0.0 Build 20200918 Rel. 58628

  0  
  0  
#48
Options
Re:TL-R605 not visible in Dashboard and Speedtest loop
2021-04-08 00:54:04

Dear @syl3nt,

 

syl3nt wrote

I have the same issue described here and I have all the software on the latest version possible.

The gateway info is always "N/A" and the speedtest always gives me an error. (even with the periodic test enabled) 

 

TL-R605v1 | 1.0.1 Build 20210113 Rel.35074

TL-SG2008Pv1 | 1.0.0 Build 20200608 Rel.76470

OC200v1 | version 4.2.11 | 1.7.4 Build 20210118 Rel.72627

2x EAP-225v3 | 5.0.0 Build 20200918 Rel. 58628

 

Could you please provide some screenshots of the error page for checking?

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  1  
  1  
#49
Options
Re:TL-R605 not visible in Dashboard and Speedtest loop
2021-04-08 01:30:08 - last edited 2021-04-08 01:44:16

@Fae 

 

This is how the dashboard always looks.

ahm... ok .. upon changing some things on my end, namely the isp, and consequently the dns servers, the speedtest is now done with 0 errors O.o

 

anyway I inspected the page and the request was sent, tried 5 times for response from the gateway and then it gave the error with a red "X" saying that an error occured.

 


I still need to check if it could be any of the configurations on Cloudflare gateway since its an isp fresh installation and am not currently using them.

I'll give more feedback on this after some periodic speed tests too.

 

  0  
  0  
#50
Options
Re:TL-R605 not visible in Dashboard and Speedtest loop
2021-04-08 02:55:18

Dear @syl3nt,

 

syl3nt wrote

ahm... ok .. upon changing some things on my end, namely the isp, and consequently the dns servers, the speedtest is now done with 0 errors O.o

anyway I inspected the page and the request was sent, tried 5 times for response from the gateway and then it gave the error with a red "X" saying that an error occured.
I still need to check if it could be any of the configurations on Cloudflare gateway since its an isp fresh installation and am not currently using them.

I'll give more feedback on this after some periodic speed tests too.

 

Thank you for your valued feedback. 

 

Any further assistance needed or any additional information to provide on this issue, please feel free to reply to this post.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  1  
  1  
#51
Options
Re:TL-R605 not visible in Dashboard and Speedtest loop
2021-04-10 02:23:32 - last edited 2021-04-10 02:25:20

@Fae 


So after testing, i was correct, Cloudflare Gateway wasn't the problem, my previous isp blocked the connection idk why.

 

Oh, also.. if you could give us the option to select what server we want the speed test to take part, that way I won't be always limited to the automatically selected server that only goes up to 470 +- Mbps on my gigabit connection.

 

I think it would be pretty easy to implement since you just need to make it so we can edit the server id on the command sent, and we can consult the server id on this list "https://c.speedtest.net/speedtest-servers-static.php".

  3  
  3  
#52
Options
1456
Related Articles
Tl-r605 omada controlled properly connected but non visible on Dashboard Omada SDN
1572 0
TL-R605 IPv6
1618 3
TL-R605 Performance
7650 1
Deploying the TL-R605...
934 0
System or Site time visible in dashboard?
72 0
 Speed test limited on TL-R605
2695 1
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.