Business Community > All Threads > Access Modem UI connected to ER605
< All Threads

Access Modem UI connected to ER605

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Access Modem UI connected to ER605

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Access Modem UI connected to ER605
Access Modem UI connected to ER605
2023-09-20 13:52:57
Tags: #WAN Setup #Routing #ModemUI
Model: ER605 (TL-R605)  
Hardware Version: V2
Firmware Version: 2.1.2

I have my ISP provided modem (ISP router in bridge mode) connected to ER605 in an Omada controller enviroment. How can i access the Modem web UI from LAN? The Modem is on subnet 192.168.1.0/25 and ER605 on 172.27.27.0/24.

  0      
 
  0      
 
#1
Options
4 Reply
Re:Access Modem UI connected to ER605
2023-09-20 16:04:42

  @youbarajsha 

 

What's the management IP of the modem when in bridged mode?  You just need to create a static route for that IP/subnet via the WAN port.

 

 

<< Paying it forward, one juicy problem at a time... >>
  0  
  0  
#3
Options
Re:Access Modem UI connected to ER605
2023-09-22 05:53:16 - last edited 2023-09-22 13:03:29

  @d0ugmac1 Thanks for the info. Can you help me a little more here. My bridge mode ip to access the modem is 192.168.1.1 and my LAN is on 172.27.27.1. I know there is an option Transmission -->Routing-->Static Route in Omada controller and ER605, but I am not sure how to set it up exactly. Much thanks.

 

So far I have done the follwing but still not able to access the modem at 192.168.1.1

 

Transmission --> Routing --> Static Routing

Name - ISP Modem

Status - Enabled

Destination IP/Subnet: 192.168.1.1/32

Route Type:  Interface

Interface: WAN

  0  
  0  
#4
Options
Re:Access Modem UI connected to ER605
2023-09-23 02:54:58

  @youbarajsha 

 

Here what I used back when I had Starlink at one of my sites.  Just change the 192.168.100.1/24 subnet to 192.168.1.1/24 and you should be good.

 

 

 

<< Paying it forward, one juicy problem at a time... >>
  1  
  1  
#5
Options
Re:Access Modem UI connected to ER605
2023-09-23 20:12:11 - last edited 2023-09-23 20:16:35

  @youbarajsha 

 

So far I was able to avoid those modem/router combos so I’m not sure about your issue. Also, it looks like the bridge mode can mean different things depending on the combo. However it looks like you are trying to access the LAN side of the combo, not the modem. In that case, I think you just can’t do it from behind the ER605. I don’t think there is a gateway you can use for it. You would need to connect your PC/laptop directly to the ISP router and have it in the same subnet as the router.

Kris K
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 1454

Replies: 4

Tags

WAN Setup Routing
ModemUI
Related Articles
ER605 v2 USB Modem not connected
1695 0
ER605 v2 - No USB modem connected.
1024 0
ER605 access to WAN modem admin page
875 0
Access Modem Admin Site
394 0
ER605 no access to web interface (UI)
4570 3
ER605 second WAN Port is connected but doesn't go online
304 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.