Business Community > All Threads > TP-LINK TL-SG1016DE Trunking
< All Threads

TP-LINK TL-SG1016DE Trunking

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TP-LINK TL-SG1016DE Trunking

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TP-LINK TL-SG1016DE Trunking
TP-LINK TL-SG1016DE Trunking
2022-11-09 20:12:18 - last edited 2022-11-10 20:55:37
Model: TL-SG1016DE  
Hardware Version: V2
Firmware Version: 1.0.1 Build 20151218 Rel.58739

Hi

 

I know this switch doesn't support LACP, So I am trying to set up a new nas with 2 ports, 

 

I have the options to set a bond type on the NAS to the below

 

Round-robin (balance-rr)

Active-backup (active-backup)

XOR (balance-xor)

Broadcast (broadcast)

IEEE 802.3ad Dynamic link aggregation (802.3ad, LACP)

Adaptive transmit load balancing (balance-tlb)

Adaptive load balancing (balance-alb)

 

So which would be the option i can use and is best, would i set this first?

 

then on routers just set up Trunk with the 2 ports im going to use?

 

thanks

 Carl

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:TP-LINK TL-SG1016DE Trunking-Solution
2022-11-10 18:33:59 - last edited 2022-11-10 20:55:37

  @cah1982 

 

No, you always create a LAG group on the switch first. Just use one cable initially. Connect the other one once you finished the setup.

Kris K
Recommended Solution
  0  
  0  
#4
Options
4 Reply
Re:TP-LINK TL-SG1016DE Trunking
2022-11-10 17:40:12

  @cah1982 

 

So which would be the option i can use and is best, would i set this first?

 

XOR (balance-xor)

 

You can try Round-robin (balance-rr), but that may result in many retransmissions due to out of sequence packets. You can not use IEEE 802.3ad Dynamic link aggregation (802.3ad, LACP) as you already know and Broadcast (broadcast) is apparently for some special cases. The others are to be used with switches that do not support LAG at all. I think Adaptive load balancing (balance-alb) is best in such cases.

 

then on routers just set up Trunk with the 2 ports im going to use?

 

Yes, but only if Trunk means link aggregation as opposite to a trunk in a VLAN configuration.

Kris K
  0  
  0  
#2
Options
Re:TP-LINK TL-SG1016DE Trunking
2022-11-10 18:28:16

  @KJK 

 

I was selecting ports 1,3 and adding it here

 



XOR (balance-xor) < are you saying this is the best to use?

So would i set it up on NAS first and apply the settings, then change the Switch trunking, as last time when i enabled the switch, it wouldnt let me connect to NAS

  0  
  0  
#3
Options
Re:TP-LINK TL-SG1016DE Trunking-Solution
2022-11-10 18:33:59 - last edited 2022-11-10 20:55:37

  @cah1982 

 

No, you always create a LAG group on the switch first. Just use one cable initially. Connect the other one once you finished the setup.

Kris K
Recommended Solution
  0  
  0  
#4
Options
Re:TP-LINK TL-SG1016DE Trunking
2022-11-10 20:56:37

  @KJK 

 

Cheers using XOR, it can go up to 100MBs for one transfer and 30-40MBs from other PC at same time

  1  
  1  
#5
Options

Information

Helpful: 0

Views: 1507

Replies: 4

Related Articles
Trunking Help: ER-X > SG1016DE >SG1016DE>EAP225
1874 0
VLAN trunking iwth TL-SG1016DE ?
826 0
TP-LINK SG1016DE Port Trunking
3957 0
TP-LINK TL-SG1016DE + QOS
1540 0
What is the difference between switches TL-SG1016D and TL-SG1016DE?
4643 0
TL-SG1016DE Port Trunking
1927 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.