Home

Forums

Stories

Knowledge Base

Business Community > All Threads > TL-SX3008F v.1.0 change SFP+ to SFP via CLI commands

< All Threads

TL-SX3008F v.1.0 change SFP+ to SFP via CLI commands

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TL-SX3008F v.1.0 change SFP+ to SFP via CLI commands

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

axiscomputers

2021-09-14 09:42:31

Posts: 1

Helpful: 2

Solutions: 0

Stories: 0

Registered: 2021-09-14

TL-SX3008F v.1.0 change SFP+ to SFP via CLI commands

2021-09-14 09:42:31

Model: TL-SX3008F

Hardware Version: V1

Firmware Version:

Hello,

We have TL-SX3800F v.1.0 with TL-SM321A and MC220L witch TL-SM321B on other side. TL-SX3800F have 8xSFP+ (10G) ports and we need switch ports via concole on TL-SX3800F to SFP (1G), to work with TL-SM321A. I can connect to switch via console (with PUTTY) but I don know CLI commands to change SFP+ to SFP mode on ports. Can you helm me please ?

Thanks.

2 Reply

Emitplink

LV3

2021-09-14 20:42:23

Posts: 130

Helpful: 46

Solutions: 21

Stories: 0

Registered: 2020-02-11

Re:TL-SX3008F v.1.0 change SFP+ to SFP via CLI commands

2021-09-14 20:42:23

@axiscomputers

Check the CLI guide: https://static.tp-link.com/2020/202011/20201103/1910012904_T16_T26_CLI.pdf (page 41)

You have to enter in enable mode, config, and then configure the ten gigabit port number and set the speed to 1000.

Fae

2021-09-24 08:34:08

Posts: 3613

Helpful: 1357

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:TL-SX3008F v.1.0 change SFP+ to SFP via CLI commands

2021-09-24 08:34:08

Dear @axiscomputers,

axiscomputers wrote

We have TL-SX3800F v.1.0 with TL-SM321A and MC220L witch TL-SM321B on other side. TL-SX3800F have 8xSFP+ (10G) ports and we need switch ports via concole on TL-SX3800F to SFP (1G), to work with TL-SM321A. I can connect to switch via console (with PUTTY) but I don know CLI commands to change SFP+ to SFP mode on ports. Can you helm me please ?

The TL-SX3800F in Controller mode is configured with 10G ports by default. For your case, you can try the Beta firmware provided in this post.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

axiscomputers

2021-09-14 09:42:31

Posts: 1

Helpful: 2

Solutions: 0

Stories: 0

Registered: 2021-09-14

Information

Helpful: 2

Replies: 2

TL-SX3008F v.1.0 change SFP+ to SFP via CLI commands

TL-SX3008F v.1.0 change SFP+ to SFP via CLI commands

Information

Voters 0

Tags