Home

Forums

Stories

Knowledge Base

Business Community > All Threads > Force a VOIP phone to 1 wan

< All Threads

Force a VOIP phone to 1 wan

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Force a VOIP phone to 1 wan

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

jcpamart

2020-12-01 11:39:48 - last edited 2021-04-18 10:35:18

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2020-11-12

Force a VOIP phone to 1 wan

2020-12-01 11:39:48 - last edited 2021-04-18 10:35:18

Model: TL-ER5120

Hardware Version: V2

Firmware Version:

Hi,

I have now 2 access on my router.

1 ADSL aprox : 8 Mb/s

1 wifimax aprox : 30 Mb/s

My VOIP phone gigaset is work correctly, but cut after many minutes of conversation.

Do you think it should be good to force the phone to access at only 1 WAN port ?

If yes, how can I do it ?

Cause it's not a server, and I don't think port triggering should be the solution.

Thanks for your help

Best regards

1 Accepted Solution

Fae

2020-12-02 03:46:05 - last edited 2021-04-18 10:35:18

Posts: 3604

Helpful: 1360

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:Force a VOIP phone to 1 wan-Solution

2020-12-02 03:46:05 - last edited 2021-04-18 10:35:18

Dear @jcpamart,

My VOIP phone gigaset is work correctly, but cut after many minutes of conversation.

Do you think it should be good to force the phone to access at only 1 WAN port ?

If yes, how can I do it ?

If you want to try, configure policy routing to force the phone to access the specific WAN port.

Protocol: ALL. Source IP: IP address of VOIP phone. Destination IP: 0.0.0.0 WAN: Select the desired WAN port.

In addition, is the SIP ALG enabled or disabled? You could try changing the SIP ALG status for checking.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

Recommended Solution

2 Reply

Fae

2020-12-02 03:46:05 - last edited 2021-04-18 10:35:18

Posts: 3604

Helpful: 1360

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:Force a VOIP phone to 1 wan-Solution

2020-12-02 03:46:05 - last edited 2021-04-18 10:35:18

Dear @jcpamart,

My VOIP phone gigaset is work correctly, but cut after many minutes of conversation.

Do you think it should be good to force the phone to access at only 1 WAN port ?

If yes, how can I do it ?

If you want to try, configure policy routing to force the phone to access the specific WAN port.

Protocol: ALL. Source IP: IP address of VOIP phone. Destination IP: 0.0.0.0 WAN: Select the desired WAN port.

In addition, is the SIP ALG enabled or disabled? You could try changing the SIP ALG status for checking.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

Information

Helpful: 0

Replies: 2

Force a VOIP phone to 1 wan

Force a VOIP phone to 1 wan

Information

Voters 0

Tags