Business Community > All Threads > TPLINK EAP 225 V3 Briked After Firmware Update
< All Threads

TPLINK EAP 225 V3 Briked After Firmware Update

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TPLINK EAP 225 V3 Briked After Firmware Update

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TPLINK EAP 225 V3 Briked After Firmware Update
TPLINK EAP 225 V3 Briked After Firmware Update
2020-03-27 21:24:11 - last edited 2020-03-27 21:27:05
Model: EAP225  
Hardware Version: V3
Firmware Version: 2.61

Hey Guys,

 

I am using TPLINK EAP 225 v3 as a standalone access point connected directly to a POE Switch.

 

During Firmware update to Firmware 2.7.0, something went wrong, and I can no longer access the WEB UI - while users still can access WIFI.

 

I have hard reset the EAP, and still no luck - the name of the SSID is back to default, however, no mean of ability to interact with it through Web UI. 

 

I am sure that this is firmware related, and I want to flash the firmware again. I need the instructions to flash the firmware without using WEB UI, as it's not working in my case.

 

I have found many tutiorials online, but they are all consumer-grade access points related. I need one specificaly made for EAP business line.

 

Looking forward to your feedback.

 

Rashid

  0      
 
  0      
 
#1
Options
4 Reply
Re:TPLINK EAP 225 V3 Briked After Firmware Update
2020-03-28 09:41:08

 

RAlkaabi wrote 

I have hard reset the EAP, and still no luck - the name of the SSID is back to default, however, no mean of ability to interact with it through Web UI. 

 

If the factory reset did work by resetting the SSID to the default SSID, the EAP is almost certainly not bricked.

 

To check, connect the EAP to your PC, set the PC's IP address to 192.168.0.10 and load the web UI of the EAP using its default IP 192.168.0.254. Configure settings and reconnect the EAP to the network.

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#2
Options
Re:TPLINK EAP 225 V3 Briked After Firmware Update
2020-03-28 12:34:53

Thanks @R1D2 !

 

I tried doing that, however, Web UI still doesn't load. In fact, I can ping the Access point, but still no chance of accessing the Web UI. 

 

Is there a manual for flashing firmware on this device? 

  0  
  0  
#3
Options
Re:TPLINK EAP 225 V3 Briked After Firmware Update
2020-03-29 10:39:17

 

RAlkaabi wrote

Is there a manual for flashing firmware on this device? 

 

You mean for recovery of the firmware? No. But if you think it's bricked, contact TP-Link support by mail (see your country's TP-Link website for contact information). Consider to apply for RMA.

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#4
Options
Re:TPLINK EAP 225 V3 Briked After Firmware Update
2020-03-29 15:19:34

Thanks @R1D2 !

 

if there is any workaround to Flash firmware, please let me know.

  0  
  0  
#5
Options

Information

Helpful: 0

Views: 1741

Replies: 4

Related Articles
EAP 225 V3 new firmware?
3528 0
EAP 225 - Backdored by the update ?
590 0
TPlink Eap 225 V3 firmware update version 2.6.1
1688 1
EAP 225 v3 with POE IP Camera
2800 0
EAP 225 v3 EU Indoor - 802.3af POE not working
2706 0
Firmware for EAP 225 V3
2517 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.