TP-Link Community

I've just ordered an EAP772, but will not be using PoE so need to also order a DC power supply. I've searched online but can't find out exactly what dimension I need for the barrel connector that plug

By tRiFFiD · Latest post 56 minutes ago

0Helpful

6Views

0Replies

Beta SoftwareEAP620 HD_V3_1.4.90 Beta Firmware (Released on 3rd April, 2025)

This Article Applies to: EAP620 HD_V3 Fully Adapted to Omada SDN Controller v5.15 or above Release Notes: New Features/Enhancements: 1. Add support to display the configuration synchronization status

By

Vincent-TP · Latest post 5 hours ago

0Helpful

33Views

0Replies

Omada Controller - Bind to AP logic.

Self-hosted Omada Software Controller: v 5.15.20.18 EAP610 v3 Firmware: 1.5.0 Build 20240830 Rel. 63168 The "Bind to AP" indeed works as intended. However, once the EAP ap device is "forget" from the

Network ConnectivityMeshBind

By Joolsc · Latest post 5 hours ago

0Helpful

7Views

0Replies

IP groups, and not just networks, should be able to be set as targets for DPI / Applicaiton Control

In DPI / Application control, we can currently only set Networks (ie, router interfaces) as targets for DPI. We should also be allowed to set IP groups. Switch only VLANs do not exist on the gateway,

By GRL · Latest post 11 hours ago

0Helpful

12Views

0Replies

Vigi C340 cameras/Cannot link to my TP-Link account

Hello, I am looking for advice regarding TP-Link security manager. I have bought 3 Vigi C340 cameras and was able to find these on local account in the security manager (can view them, set them up, ev

VIGI CameraSecurity Manager

By Jacksparkour · Latest post 5 hours ago by Clive_A

0Helpful

23Views

1Replies

EAP225 outdoor corrupt update

Hi, I just recently upgrade my firmware but the power outage occur and my EAP is not showig in omada portal and it keeps on blinking green for 5sec then grenn and orange repeat cycle. Tried to hard re

Firmware UpdateNetwork ConnectivityInstallationPortal

By Jeffjeff · Latest post 16 hours ago

0Helpful

16Views

0Replies

ADD NEW SWITCH PROBLEM

Hello, my router ip is 192.168.0.1 When i adopt a new switch by default omada controller gives 192.168.0.1 ip and i have network problem. When i setup a new switch before connect it with omada and i g

Configuration

By MihalisK · Latest post 5 hours ago by Clive_A

0Helpful

33Views

1Replies

CPE510 RADIATION COVERAGE IN REPEATER MODE

I have convigured a CPE510 as a repeater, connected to a CPE710 AP, I'm interested to know what is the "Radiation" signal strength behind the CPE510 when connecting additional CPE510 to the repeater?

Repeater/Bridge ModeNetwork ConnectivityOutdoor Wi-Fi Solution

By EReid20 · Latest post 19 hours ago

0Helpful

10Views

0Replies

No statistics on ISP panel

Hi all Yesterday I had to reboot the controller in a customer of mine because it was operating weird, with several moments that seemed to be struggling and not being able to access it locally or in th

ControllerPortalLogs

By digitalFounders · Latest post 23 hours ago

0Helpful

26Views

0Replies

DHCP with VLAN not working

Hi, I have just bought TPLink EAP683 UR AP. My setup is Microsoft NPS for authentication and DHCP server, both configured on same server and network. I am trying to configure 2 SSIDs with different VL

By KBLogics · Latest post 22 hours ago by Vincent-TP

0Helpful

22Views

1Replies