Can not connect to device over LAN with ER605

Can not connect to device over LAN with ER605

19 Reply
Re:Can not connect to device over LAN with ER605
a week ago

  @irbaaz You don't need to clone MAC Addresses. When the ISP Modem/Router combo is put into "Passthrough Mode", it turns it into a ISP Modem only. Right now the Modem side gets the WAN IP and the Router side uses local IPs (192.168.*.*). Passthrough Mode will pass the WAN IP to the ER605 WAN Port.

  0  
  0  
#12
Options
Re:Can not connect to device over LAN with ER605
a week ago

  @RaRu 

Yes internet is going through router not through tp link

  0  
  0  
#13
Options
Re:Can not connect to device over LAN with ER605
a week ago
I doubt my isp modem has passthrough mode I will double check on it
  0  
  0  
#14
Options
Re:Can not connect to device over LAN with ER605
Saturday

  @irbaaz 

 

So it is like this?

 

  0  
  0  
#15
Options
Re:Can not connect to device over LAN with ER605
Saturday

  @RaRu 

yes you got it exactly right.

 

I have one question is bridge mode is passthorugh mode on router ?

  0  
  0  
#16
Options
Re:Can not connect to device over LAN with ER605
Saturday - last edited Saturday

  @irbaaz 

 

I don't think those are exactly the same things but I've seen many times those being used interchangeably a lot...

 

The problem with setting your Router A/B in Passthrough mode is that it will become a modem only. So no WiFi  for your Wireless clients from that device. So you are aware.

 

On those Routers A/B - do you have a possibility to set up a static routing? Or there's no such feature?

  1  
  1  
#17
Options
Re:Can not connect to device over LAN with ER605
Monday

Hi @irbaaz 

Thanks for posting in our business forum.

irbaaz wrote

Hi I have installed this in my office to create a load balancer.

 

So 2 modems individual with PPOE wires are going in WLAN and WLAN/LAN1 and load balancing working fine.

 

now all network output to wired devices are going through router, I want to access my server which has IP 192.168.0.XX 

Through other devices connected to wired network I can communicate.

 

But through WIFI network (that is created with original 2 routers that is connect to ER605) I can not communicate to my server as well my printer connected to network via LAN I can not access same through WIFI.

Inside the orange, you need the mDNS if you have multi-VLAN.

Devices in the ER605 can access A and B LAN but you have to know their IP addresses first.

From A and B, if you need to access devices in ER605, port forward.

Best Regards! If you are new to the forum, please read: Howto - A Guide to Use Forum Effectively. Read Before You Post. Look for a model? Search your model NOW Official and Beta firmware. NEW features! Subscribe for the latest update!Download Beta Here☚ ☛ ★ Configuration Guide ★ ☚ ☛ ★ Knowledge Base ★ ☚ ☛ ★ Troubleshooting ★ ☚ ● Be kind and nice. ● Stay on the topic. ● Post details. ● Search first. ● Please don't take it for granted. ● No email confidentiality should be violated. ● S/N, MAC, and your true public IP should be mosaiced.
  1  
  1  
#18
Options
Re:Can not connect to device over LAN with ER605
Monday

  @irbaaz 

 

Ideally your setup should look like this:

 

Network

 

You can either create VLANs on the default LAN port or use the extra LAN ports on the ER605 to create separate networks. Each Network/VLAN should have its own subnet like the IP suggestions above. By default, the networks will be isolated from each other. You need to create Firewall Access Rules on the ER605 to allow the networks to talk to each other. If you can't put the A and B routers into Access Point Mode, you will need to create routes on the router that sends traffic to the VLAN 1 Resources.

 

Note: VLAN 1 is the default on network devices (Routers and Switches) and does not need to be configured or changed. You can change the subnet though.

  0  
  0  
#19
Options
Re:Can not connect to device over LAN with ER605
Monday

  @irbaaz 

 

Alternate configuration:

If you have Modem/Router Combos from the ISP, try the following setup. You will need to setup static Routes on each router to get the separate networks to talk to each other with two way traffic.

Network

  0  
  0  
#20
Options