LACP issue after REBOOT

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

LACP issue after REBOOT

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
LACP issue after REBOOT
LACP issue after REBOOT
2023-04-09 15:36:33

Hello community!

 

I got a strange problem by 2 of my customers with Omada + LACP

 

the one is using

TL-SG3452 v1.0 and TL-SG3452P v1.0 with LACP (2 Ports)

 

another one is using

TL-SG3428 v2.0 and TL-SG2428P v1.0 with LACP (3 Ports)

 

ISSUE:

customer nr 1 with 52er switches had the problem since ever

customer nr 2 with 24er switches since update switch/omada

 

When I reboot router, controller or one of the switches, or both, or everything - the network is down, until I disconnect cables, connected to LACP ports, but one.

After only ONE cable is connected, network starts working again.

 

Router is reachable over the internet - so the issue is between the 2 switches. After consulting german tp-link technician pro, we checked, if the ports have the loop detection BEFORE I activate LACP. But the issue still exists.

 

funny but true: static LAG is working without issue.

 

can someone help please?

 

thank you

Regards

Alex

 

 

  0      
  0      
#1
Options
5 Reply
Re:LACP issue after REBOOT
2023-04-10 11:11:16

Hello @kogan,

 

May I know the firmware version of your switches and controller?

Is your router an Omada Gateway? What is the hardware and firmware version of it?

 

If you can show your network layout/topology, it will be more helpful.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:LACP issue after REBOOT
2023-04-10 16:08:46 - last edited 2023-04-10 16:09:59

  @Hank21 

Hi Hank21

 

thanks for the fast answer:

 

ER7206 v1.0 / 1.3.0 Build 20230322 Rel.70951

TL-SG3452 v1.0 / 1.1.7 Build 20230206 Rel.46080

TL-SG3452P v1.0 / 1.1.7 Build 20230206 Rel.46080

 

Configuration ist with VLAN, Omada ist newest, 5.9.31 - but issue exists longer

  0  
  0  
#3
Options
Re:LACP issue after REBOOT
2023-04-12 02:19:56

Hi @kogan ,

 

To better assist you, I've created a support ticket via your registered email address, and escalated it to our support engineer to look into the issue. The ticket ID is TKID230418273, please check your email box and ensure the support email is well received. Thanks!

Once the issue is addressed or resolved, welcome to update this topic thread with your solution to help others who may encounter the same issue as you did.

 

Many thanks for your great cooperation and patience!

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#4
Options
Re:LACP issue after REBOOT
2023-05-10 09:09:44

Hello @kogan,

 

Hope you are doing well. I’m wondering whether your concern was resolved finally?

If your concern was resolved, welcome to update this topic thread and share your solution so that others may benefit from it.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#5
Options
Re:LACP issue after REBOOT
2023-05-10 09:12:56

Hello  @Hank21 

 

I've got a beta firmware for the switch, but didnt try to reboot them (scared) ;-)

Tomorrow morning I am onsite and will check the situation and give feedback.

thanks

  1  
  1  
#6
Options