Home

Forums

Stories

Knowledge Base

Business Community > Switches > Not able to create static route for internet access

< Switches

Not able to create static route for internet access

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Not able to create static route for internet access

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

espitech

2023-02-09 21:03:40 - last edited 2023-02-10 07:19:05

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2023-02-09

Not able to create static route for internet access

2023-02-09 21:03:40 - last edited 2023-02-10 07:19:05

Model: TL-SG2428P

Hardware Version: V4

Firmware Version: 4.0.5

Hi,

I have to admit I'm quite new to the Omada world. Curently I have a standard Internet Wifi Router at home. But we're moving to a new house soon and I decided to setup a system with a SG2428P and two APs.

I'm now trying to define a static route on my SG2428P to my Internet Router 192.168.23.200 to access the internet. However I'm not able to enter 0.0.0.0/0 as destination IP and subnet. It says "Invalid format for IP or mask".

What am I doing wrong?

Thanks in advance for your help!

Sascha

1 Accepted Solution

Hank21

2023-02-10 07:19:01 - last edited 2023-02-10 07:19:05

Posts: 3673

Helpful: 718

Solutions: 497

Stories: 8

Registered: 2021-12-13

Re:Not able to create static route for internet access-Solution

2023-02-10 07:19:01 - last edited 2023-02-10 07:19:05

Dear @espitech

If you want to set up static routing for a specified switch, please go to Controller->Devices->Choose the switch->On the right menu go to Config->Static Route.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*

Recommended Solution

2 Reply

d0ugmac1

LV5

2023-02-09 22:44:46

Posts: 2120

Helpful: 772

Solutions: 191

Stories: 0

Registered: 2022-03-05

Re:Not able to create static route for internet access

2023-02-09 22:44:46

@espitech

Your switch is a switch, not a router, it doesn't need a route. In fact I can't see any reason why you'd even need that switch (bit like having a schoolbus to take 2 kids to school).

If you really want to use the switch, like you need the POE, plug the switch into your home router's LAN and then plug the APs into the switch.

Though you don't mention it, it looks suspiciously like you have an Omada controller in the mix somehow as well. This is fine for setting up the AP's radios, but without an Omada controlled gateway/router such as the ER605, there's not much point using it to configure your switch as anything more than a POE power bar.

<< Paying it forward, one juicy problem at a time... >>

Hank21

2023-02-10 07:19:01 - last edited 2023-02-10 07:19:05

Posts: 3673

Helpful: 718

Solutions: 497

Stories: 8

Registered: 2021-12-13

Re:Not able to create static route for internet access-Solution

2023-02-10 07:19:01 - last edited 2023-02-10 07:19:05

Dear @espitech

If you want to set up static routing for a specified switch, please go to Controller->Devices->Choose the switch->On the right menu go to Config->Static Route.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*

Not able to create static route for internet access

Not able to create static route for internet access

Information

Voters 0

Tags