Home

Forums

Stories

Knowledge Base

Business Community > Controllers > Adopting TL-R605 / SW Controller 4.4.3

< Controllers

Adopting TL-R605 / SW Controller 4.4.3

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Adopting TL-R605 / SW Controller 4.4.3

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ZdenekM

2021-07-09 09:55:44 - last edited 2021-07-13 12:14:44

Posts: 46

Helpful: 12

Solutions: 0

Stories: 0

Registered: 2021-02-26

Adopting TL-R605 / SW Controller 4.4.3

2021-07-09 09:55:44 - last edited 2021-07-13 12:14:44

Model: ER605 (TL-R605)

Hardware Version: V1

Firmware Version: 1.0.1

So far, I have used the gateway in a standalone mode. With controller 4.4.3, it is possible to change the LAN subnet so I thought that adopting the gateway should be ok now, but I'm getting "username or password is incorrect" although those are certainly correct (I can log in using the same credential to the gateway's UI). Any idea what might be wrong? Log only says this:

2021-07-09 11:43:02 [nioEventLoopGroup-10-8] [WARN]-[SourceFile:180] - Handle adopt fail response from C0-C9-E3-DA-06-D3
2021-07-09 11:43:02 [qtp1396431506-3198] [WARN]-[SourceFile:239] - Adopt C0-C9-E3-DA-06-D3 failed -2: invalid credential

Btw, is there a way how to migrate static DHCP leases from the standalone gateway to the controller?

File:

Screenshot from 2021-07-09 11-43-06.pngDownload

1 Accepted Solution

Fae

2021-07-13 11:35:54 - last edited 2021-07-13 12:14:44

Posts: 3614

Helpful: 1371

Solutions: 475

Stories: 0

Registered: 2020-06-30

Re:Adopting TL-R605 / SW Controller 4.4.3-Solution

2021-07-13 11:35:54 - last edited 2021-07-13 12:14:44

Dear @ZdenekM,

ZdenekM wrote
So far, I have used the gateway in a standalone mode. With controller 4.4.3, it is possible to change the LAN subnet so I thought that adopting the gateway should be ok now, but I'm getting "username or password is incorrect" although those are certainly correct (I can log in using the same credential to the gateway's UI). Any idea what might be wrong? Log only says this:
2021-07-09 11:43:02 [nioEventLoopGroup-10-8] [WARN]-[SourceFile:180] - Handle adopt fail response from C0-C9-E3-DA-06-D3
2021-07-09 11:43:02 [qtp1396431506-3198] [WARN]-[SourceFile:239] - Adopt C0-C9-E3-DA-06-D3 failed -2: invalid credential

From the previous feedback on the community, rebooting the ER605 by unplugging the power cord may help to solve the issue.

Have you tried rebooting the ER605 gateway and would a reboot of the ER605 router help?

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

Recommended Solution

3 Reply

Somnus

LV5

2021-07-12 10:18:10

Posts: 1212

Helpful: 226

Solutions: 72

Stories: 0

Registered: 2021-06-14

Re:Adopting TL-R605 / SW Controller 4.4.3

2021-07-12 10:18:10

You can log in to the web UI and change a new login username/password, or change it back to admin/admin. Or just reset it directly. I guess static DHCP leases can't be migrated. Address reservation on controller and in standalone seem to be different.

Fae

2021-07-13 11:35:54 - last edited 2021-07-13 12:14:44

Posts: 3614

Helpful: 1371

Solutions: 475

Stories: 0

Registered: 2020-06-30

Re:Adopting TL-R605 / SW Controller 4.4.3-Solution

2021-07-13 11:35:54 - last edited 2021-07-13 12:14:44

Dear @ZdenekM,

ZdenekM wrote
So far, I have used the gateway in a standalone mode. With controller 4.4.3, it is possible to change the LAN subnet so I thought that adopting the gateway should be ok now, but I'm getting "username or password is incorrect" although those are certainly correct (I can log in using the same credential to the gateway's UI). Any idea what might be wrong? Log only says this:
2021-07-09 11:43:02 [nioEventLoopGroup-10-8] [WARN]-[SourceFile:180] - Handle adopt fail response from C0-C9-E3-DA-06-D3
2021-07-09 11:43:02 [qtp1396431506-3198] [WARN]-[SourceFile:239] - Adopt C0-C9-E3-DA-06-D3 failed -2: invalid credential

From the previous feedback on the community, rebooting the ER605 by unplugging the power cord may help to solve the issue.

Have you tried rebooting the ER605 gateway and would a reboot of the ER605 router help?

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

Adopting TL-R605 / SW Controller 4.4.3

Adopting TL-R605 / SW Controller 4.4.3

Information

Voters 0

Tags