I have been able to test this week, strangely I had internet access this time around. One thing I couldn't see is to send all traffic through the vpn instead of local traffic, is it possible to edit the server config file to include redirect-gateway?

I connected to the OpenVPN server with my laptop. 

Execute "route print" command and you will find the route tables.

I found that two routes were added, one is 0.0.0.0 mask 0.0.0.0 go via OpenVPN Interface;

the second is 192.168.10.0 mask 255.255.255.0 go via OpenVPN Interface;

But 0.0.0.0 mask 0.0.0.0 go via my ethernet adapter has a higher priority, so all the Internet requests are going from the Internet rather than the VPN.

@Fae it was brought to my attention by an TP-representative from the Netherlands, this problem might be solved in Omada 4.3. together with firmware upgrades for the omada hardware.

When will this version be available to the public?

@joeri1 and @Fae 

Earlier this week I got my hands on firmware version 1.0.1 Build 20210113 Rel.35074 for my TL-R605 v1.0

This didn't fix the VPN issue.

Yesterday I upgraded my software controller from version 4.2.8 to version 4.2.11

This also didn't fix the VPN issue.

@joeri1 @Fae 

I have the same problem with openvpn.

I can connect to the lan but I cannot browse internet.

I have a TL-R605 in SDN configuration with 2 lans

192.168.0.1/24

192.168.1.1/24

The openvpn is configured this way

I also updated the firmware and the omada software that run on a windows pc in the first lan 

@massimilianop 

Hi,

try to use OpenVPN GUI as a client.

Regards

@Emitplink 

With openvpn gui I can browse internet but using my local dns, so the traffic is not encrypted (?)

Is it possible to use the remote network?

Hi Gyus,

I have configure openvpn server and clients has 192.168.80.0/24

I think problem is with DNS resolving,

I can ping 8.8.8.8

C:\Users\peter>ping 8.8.8.8

Pinging 8.8.8.8 with 32 bytes of data:
Reply from 8.8.8.8: bytes=32 time=10ms TTL=118
Reply from 8.8.8.8: bytes=32 time=10ms TTL=118

but I can not ping www.sme.sk because following:

Users\peter>nslookup wwww.sme.sk
DNS request timed out.
    timeout was 2 seconds.
Server:  UnKnown
Address:  192.168.80.1

DNS request timed out.
    timeout was 2 seconds.
DNS request timed out.
    timeout was 2 seconds.
DNS request timed out.
    timeout was 2 seconds.
DNS request timed out.
    timeout was 2 seconds.
*** Request to UnKnown timed-out

my ipconfig :

IPv4 Address. . . . . . . . . . . : 192.168.80.6(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.252
   Default Gateway . . . . . . . . . :
   DHCPv6 IAID . . . . . . . . . . . : 318832596
   DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-26-68-C7-1F-5C-80-B6-F8-1E-2F
   DNS Servers . . . . . . . . . . . : 192.168.80.1

                                       8.8.8.8

my question is why TPLINK configure DNS like this?

why there is no possibilty to configure dns by myself?

And why default second DNS is 8.8.8.8?

ANY answer from TPLINK?