Under Consideration 4 way switch
Release a kasa four way smart switch product, or add functionality for two three way switch products to implement a four way solution.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
hoping for clarification on the 4-way (or 5-way) switch setup using HS210kit at 3-way switch locations.
The hs210 has 2 traveller poles, and 1 dual pole for line/load. Did you only connect a single traveller to each hs210 in your 4-way config with a traditional 4 way switch in the middle?
thanks
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I have a 4 way switch. I tried to install the Kasa 3 Way Switch in 2 of the switches. I setup WiFi and paired the light. I had one of
my hallway lights that came on but very dimm. I could not get the kids them to turn on or off with app or on any of the 3 switches.
Here is the weird thing.
Switch 1 downstairs has 4 wires.
Black, White, Red, Green
Installation was a breeze but still not working.
Switch 2 Master Bedroom has
Black, Black, Red, Green (these 4 were used in old switch but there were more in junction box)
I had 2 whites that were together with wire nut
I had 1 white and 1 black that were together with wire nut.
I tried to connect the new 3 way to this switch.
I put black to black. I used the black and red as the travelers, I connected green to ground, I connected white to the two whites that were wire nut together.
Switch 3 I did not touch. It does have multiple wires like Switch 2.
How do I got about configuring my 3 way Kasa Swirch to work?
Thanks in advance.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I built a test rig to test this works, before i installed it in my house. It works just fine, as long as you replace all both three-ways and ignore teh four-ways it will work. Another place of contention is you need to porgram the power side three-way first as the primary, and the load side three-way as the secondary.
Google implementation also works well to control this setup.
- Copy Link
- Report Inappropriate Content
Thanks for all the guidance...I have now installed a 6 way switch (5 switches and outside lights). Followed the guidance in this and previous posts, and the wiring aspect worked immediately.
However, I encountered a problem running a schedule with the App...tried on at sunset off at sunrise, specific time on and off, etc and lights would turn on, but would never turn off.
Chatted with Kasa support, and they had me reinstall app....didn't fix it.
Finally, for some reason decided to set 2 time "on's" instead of a time on and a time off. And that worked....so now, for example, have schedule of lights on at sunset, and again lights on at sunrise....and goes on at sunset and off at sunrise.
No idea why this works...or whether I have a faulty Kasa switch, or whether it is an App/software issue. Seems it should be an issue for 3 or 4 way switch as well, but assume no one else has experienced since no posts to that effect.
- Copy Link
- Report Inappropriate Content
@AustinTX all I would suggest is that you check the load side three way is indeed programmed and powered up not red LED or powered off. You should also have only one entity for the switch in the kasa app while both switches are powered and not red. If you have an entity for ea h three way that's not correct.
- Copy Link
- Report Inappropriate Content
@septer012 this is all very good.
I am a DIYer... just moved into a home that has an extraneous amount of switches controlling the same light (4-way system). I just need a single kasa dimmer switch (HS220) to work, let me know what you think about this plan:
I was going to close off both of the 3-way switches and make them permanently "on". To achieve this, I would combine one of the travelers with the load wire, and then cap off the other traveler; this would make the switch permanently "on". I would repeat this for the other 3-way switch.
Then I would take the 4-way switch (double-pole), and convert to a single pole (ehow website has a good article that I can't directly link in this forum), and install to HS220.
What do you guys think?
- Copy Link
- Report Inappropriate Content
Thank you for sharing. It sure would be nice if TP-Link would test this application of their product and publish it.
- Copy Link
- Report Inappropriate Content
I got this working with only one smart switch. I installed it on the line (hot) side, and it works just fine. There is a slight delay in it sensing whether or not the light is on, but it might be a second or two.
I was originally thinking you HAD to install it on the line side to get it working, but I think I'm wrong. It should honestly work in either position. If everything is wired correctly, it should get power no matter what, and be able to sense whether or not the light is on based on how much current is flowing through the switch. I'm not sure why it didn't work for board4mic, but its working a charm for me.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 35
Views: 108723
Replies: 138