Home Network Community > All Threads > AX3000 Filling Up System Log
< All Threads

AX3000 Filling Up System Log

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

AX3000 Filling Up System Log

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
AX3000 Filling Up System Log
AX3000 Filling Up System Log
2021-01-29 13:43:47
Model: Archer AX3000  
Hardware Version: V1
Firmware Version: 1.0.4 Build 20200426 rel.69563(5553)

Hello

I have an AX3000 that I have had for about 2 weeks.  With my ISP I was getting 120Mbps down and 11Mbps up.  This is both wired and wireless.  Earlier this week I was having severe Wireless degradation getting only 7 getting wireless.  Wired was fine.  I had not made any configuration changes prior to experiencing the issue. Tried rebooting, unplugging, etc.  Ended up having to restore to factory.  That took care of it. 

For grins and giggles  I manually reloaded the latest firmware.  

 

Looking at the system log I am seeing constan INFO level messages regaring the Led Controller switching on and off a few times a second. Tried to clear the log but it wont.  Turned off the LEDs but am still getting the messages in the log. 

 

Do I have a bad unit?   Here are some of the entries in the log.

 

####################################################################
2021-01-29 08:27:43 led-controller[1444]: <6> 288051 Start to run WAN1_ON
2021-01-29 08:27:43 led-controller[1444]: <6> 288051 Start to run WAN0_OFF
2021-01-29 08:27:43 led-controller[1444]: <6> 288051 Start to run LAN_ON
2021-01-29 08:27:39 led-controller[1444]: <6> 288051 Start to run WAN1_ON
2021-01-29 08:27:39 led-controller[1444]: <6> 288051 Start to run WAN0_OFF
2021-01-29 08:27:39 led-controller[1444]: <6> 288051 Start to run LAN_OFF
2021-01-29 08:27:24 led-controller[1444]: <6> 288051 Start to run WAN1_ON
2021-01-29 08:27:24 led-controller[1444]: <6> 288051 Start to run WAN0_OFF
2021-01-29 08:27:24 led-controller[1444]: <6> 288051 Start to run LAN_ON
2021-01-29 08:27:21 led-controller[1444]: <6> 288051 Start to run WAN1_ON
2021-01-29 08:27:21 led-controller[1444]: <6> 288051 Start to run WAN0_OFF
2021-01-29 08:27:21 led-controller[1444]: <6> 288051 Start to run LAN_OFF
2021-01-29 08:27:19 led-controller[1444]: <6> 288051 Start to run WAN1_ON
2021-01-29 08:27:19 led-controller[1444]: <6> 288051 Start to run WAN0_OFF
2021-01-29 08:27:19 led-controller[1444]: <6> 288051 Start to run LAN_ON
2021-01-29 08:27:17 led-controller[1444]: <6> 288051 Start to run WAN1_ON
2021-01-29 08:27:17 led-controller[1444]: <6> 288051 Start to run WAN0_OFF
2021-01-29 08:27:17 led-controller[1444]: <6> 288051 Start to run LAN_OFF
2021-01-29 08:27:15 led-controller[1444]: <6> 288051 Start to run WAN1_ON
2021-01-29 08:27:15 led-controller[1444]: <6> 288051 Start to run WAN0_OFF
2021-01-29 08:27:15 led-controller[1444]: <6> 288051 Start to run LAN_ON

  0      
 
  0      
 
#1
Options
4 Reply
Re:AX3000 Filling Up System Log
2021-01-29 15:28:31

@PHolder 

 

I don't think think the RESET actually takes you back to factory but basically removes all settings.

 

This is what my router manual says for the back button and I assume it is the same for all routers?

 

Reset Button - Press this button for more than 5 seconds to reset the router to its factory
default settings.

 

It will not change the f/w.

 

I suggest doing the RESET again, and then power off and on. Now before restoring your settings check the log and see if it is still happening. If it is I'd try the reload of the f/w and reset again and check the log. Still happening, contact Support.

 

If not, reload your settings, and check the log. If still happening, well, the settings file could be the problem. In that case, do the reset again and MANUALLY enter your settings. Should solve the problem.

  2  
  2  
#2
Options
Re:AX3000 Filling Up System Log
2021-01-29 16:47:57
Thank you. I did do the reset again and have been monitoring the log. So far so good.
  0  
  0  
#3
Options
Re:AX3000 Filling Up System Log
2021-02-01 18:17:57 - last edited 2021-02-01 18:18:58

I have finally figured out what these log entries are from.  

I have my home PC and my work PC hardwired to the router.  When neither of these are active, the lan LED will intermittently flash and go dark.  I believe these end up in the log.  When either of my hard wired PCs are active, this doesn't happen.  

 

Is there a way to keep these from filling up the log?

  0  
  0  
#4
Options
Re:AX3000 Filling Up System Log
2021-02-01 20:07:28
I'd suggest adding a cheap gigabit 4-port switch in between the AX3000 and your devices. That said, those entries should cause a crash...
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 982

Replies: 4

Related Articles
System log does not show admin log in
341 0
Deco S4 filling its event log after firmware update
1786 0
The system log does not record all events
453 6
Lack of System Log Entries
2671 1
Need more system log info
299 0
System Log showing restarts?
447 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.