archer ax11000
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Just bought an archer AX11000. I have a 1gbps connection at home. When i stand next to the router, i get 400 mbps. I have tested the wired connection and its close to 850 mbps.
Does this router not able to achieve these speeds? When i had 1 gbps connection and an asus wifi router i was hitting 600mbps + speed few feet away from the wireless router. That router was bought years ago and went bust just this year. Does anybody know how to get this router to hit high speeds, otherwise i am planning on returning this weekend.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@jaidev I just spent 2 days debugging the same problem. Then I spent an entire afternoon chatting with TP-Link support. After all that wasted time and running around, the problem was fixed with a very simple change.
The AX11000's Speedtest function is faulty. It reports speeds just over half the speed you're actually getting.
The problem arises in that by default the AX11000's faulty Speedtest results are used to set the router's QoS (Quality of Service) capacity limits!
Solution: On a web browser, go into "Advanced" -> "HomeCare" -> "QoS" and manually edit the "Total Bandwidth" to your actual Internet service values.
My AX11000's Speedtest was returning download values in the 600 Mbps range. My actual service is 1200 Mbps. As soon as I manually edited these values, Speedtest from my 1 Gbps Ethernet attached PC went from 600 Mbps to 950 Mbps, which is what I'd expect for a 1 Gbps attached Ethernet connection.
You can verify your actual ISP's (Internet Service Provider's) delivered speeds by connecting a PC via Ethernet directly to your Modem (you'll need to power cycle it to get it to recognize your devices MAC address) and running a Speedtest that way.
Note - if you have faster than 1 Gbps service, you'll need the appropriate adapter for your PC to archive it's rated speed. 2.5 Gbps and faster USB-C adapters are available for around $30 if you need one.
Hope this helps. Let me know if it fixes your problem.
Regards,
Bill Finkelstein, retired high tech exec.
p.s. Note - Smart Connect works fine at the higher speed if you manually set the QoS values.
- Copy Link
- Report Inappropriate Content
Make sure you are not running smart connect where you just have one network name. Test the speeds on both the 5G1 band and the 5G2 band.
- Copy Link
- Report Inappropriate Content
@jaidev Read through this post "Ax11000 dropping 2.4ghz every other day". I applied the beta firmware mentioned in there several months ago and it improved my speeds and stability. To get the absolute best speed, I did need to turn off smart connect and tune it a little manually. However after applying that firmware, Smart Connect works so well I just leave it on all the time now. Good luck.
- Copy Link
- Report Inappropriate Content
@jaidev I got the this router and it seems working fine except one thing, speed test. In router admin, it has speed test and this function always give me much lower speed than other web speed test that I try, only on the down stream. The upstream is OK. For example: I get speed test from web pages is around 800 mbps, then I got tp-link speed test is around 400-550 mbps. Sometimes, it went down to 200 mbps. Is this the hardware problem, or firmware? or the tp-link speed test in the router admin is a junk?
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@jaidev I just spent 2 days debugging the same problem. Then I spent an entire afternoon chatting with TP-Link support. After all that wasted time and running around, the problem was fixed with a very simple change.
The AX11000's Speedtest function is faulty. It reports speeds just over half the speed you're actually getting.
The problem arises in that by default the AX11000's faulty Speedtest results are used to set the router's QoS (Quality of Service) capacity limits!
Solution: On a web browser, go into "Advanced" -> "HomeCare" -> "QoS" and manually edit the "Total Bandwidth" to your actual Internet service values.
My AX11000's Speedtest was returning download values in the 600 Mbps range. My actual service is 1200 Mbps. As soon as I manually edited these values, Speedtest from my 1 Gbps Ethernet attached PC went from 600 Mbps to 950 Mbps, which is what I'd expect for a 1 Gbps attached Ethernet connection.
You can verify your actual ISP's (Internet Service Provider's) delivered speeds by connecting a PC via Ethernet directly to your Modem (you'll need to power cycle it to get it to recognize your devices MAC address) and running a Speedtest that way.
Note - if you have faster than 1 Gbps service, you'll need the appropriate adapter for your PC to archive it's rated speed. 2.5 Gbps and faster USB-C adapters are available for around $30 if you need one.
Hope this helps. Let me know if it fixes your problem.
Regards,
Bill Finkelstein, retired high tech exec.
p.s. Note - Smart Connect works fine at the higher speed if you manually set the QoS values.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 2264
Replies: 6
Voters 0
No one has voted for it yet.