Home Network Community > Deco > Deco M9 Guest network not working after update to 1.6.1
< Deco

Deco M9 Guest network not working after update to 1.6.1

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco M9 Guest network not working after update to 1.6.1

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Deco M9 Guest network not working after update to 1.6.1
Deco M9 Guest network not working after update to 1.6.1
2023-07-31 14:08:53
Model: Deco M9 Plus  
Hardware Version: V2
Firmware Version: 1.6.1

My WiFi guest network will no longer work after updating to 1.6.1.

 

The SSID appears and is being broadcasted but after connecting it says "No internet, secured"

 

This happens on any Windows device. Android devices do not connect either and are never served an IP address 

 

There is a switch connected to one of the main router ports (but not in between the modem and router), and another switch connected to one of the access points, which gives Internet to another access point elsewhere in the house.

 

Any help would be greatly appreciated.

  0      
 
  0      
 
#1
Options
6 Reply
Re:Deco M9 Guest network not working after update to 1.6.1
2023-07-31 18:45:59 - last edited 2023-07-31 20:42:20

Issue is occurring only when near a specific access point.

 

All access points are wired via ethernet, expect for one that is out of range from me.

 

The one closest to me is the one having issues.

 

All switches are unmanaged.

 

See image at URL below for network topology map:

https://i.imgur.com/tagbHnn.png

  3  
  3  
#2
Options
Re:Deco M9 Guest network not working after update to 1.6.1
2023-08-01 07:43:14

  @Ouremcee 

Hi, Thanks for the feedback.

I think your issue might be like this:

https://community.tp-link.com/en/home/forum/topic/616724

Can I have the model numbers of the two network switches?

Did the network topology remain unchanged before and after the firmware upgrade?

 

Wait for your reply.

Best regards.

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! Deco BE85_1.1.1 Supports WireGuard VPN,Channel Selection and Matter Deco BE65_V2_1.1.0 Supports WireGuard VPN, Channel Selection and More ▶Deco APP 3.8.102/3.8.112-Ready for A New Deco Onboarding Experience! Try to leave a Message if urgent help is required.
  0  
  0  
#3
Options
Re:Deco M9 Guest network not working after update to 1.6.1
2023-08-01 21:22:47 - last edited 2023-08-01 21:29:01

  @David-TP Please see the updated diagram with model numbers.

 

Also below are the network switches and model numbers of those switches:

 

  • TP-Link TL-SG105
  • NETGEAR GS308v2

 

The network topology did not change, and I have only run the firmware upgrade.

 

7c4364e65e644f44a85ed64d02a9af83

  3  
  3  
#4
Options
Re:Deco M9 Guest network not working after update to 1.6.1
2023-08-02 02:08:47

  @Ouremcee 

Hi, Thanks for the update.

I see NETGEAR GS308 is an unmanaged switch, which is almost the same as TL-SG105.

But I happen to see there is a similar model NETGEAR GS308E which is an easy smart switch and supports VLAN Configuration.

Could you please confirm whether the switch is NETGEAR GS308 or NETGEAR GS308E?

 

If it is the second one with "E", I think there still needs addtional VLAN Configurations on the NETGEAR GS308E to make the guest network work properly on the third satellite Deco M9 plus:How to extend guest network when there is a switch between Decos

Or Could you please help me run a simple test:

switch the location of these two satellite M9 plus units to see whether the issue follows the same unit or the same switch.

 

Wait for your reply.

Best regards.

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! Deco BE85_1.1.1 Supports WireGuard VPN,Channel Selection and Matter Deco BE65_V2_1.1.0 Supports WireGuard VPN, Channel Selection and More ▶Deco APP 3.8.102/3.8.112-Ready for A New Deco Onboarding Experience! Try to leave a Message if urgent help is required.
  0  
  0  
#5
Options
Re:Deco M9 Guest network not working after update to 1.6.1
2023-08-02 03:21:40

@David-TP Here is the model number

 

6d49ad5cc61f4313975421c32da5756b

 

I cannot move the locations of the Deco's at the moment but can try to do so later.

  3  
  3  
#6
Options
Re:Deco M9 Guest network not working after update to 1.6.1
2023-08-03 01:57:46

  @Ouremcee 

Thanks for the update.

I will wait for your good news and at the same time, I would also like to forward your case to the senior engineers for further assistance.

Please check whether you have received an email from us.

Thank you very much.

Best regards.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! Deco BE85_1.1.1 Supports WireGuard VPN,Channel Selection and Matter Deco BE65_V2_1.1.0 Supports WireGuard VPN, Channel Selection and More ▶Deco APP 3.8.102/3.8.112-Ready for A New Deco Onboarding Experience! Try to leave a Message if urgent help is required.
  0  
  0  
#7
Options

Information

Helpful: 0

Views: 1018

Replies: 6

Related Articles
 M9 DHCP fails guest network after firmware update
367 0
 Add VLAN tag option to Deco M9 Guest network in AP-mode
2292 7
 Guest network not working
1131 0
 Guest Network - AP Mode - Isolation?
1463 0
 Deco S4 Latest Firmware Update - Guest Network Isolation
2085 1
 Deco M5 Guest Network
1011 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.