Home

Forums

Stories

Knowledge Base

Home Network Community > Deco > Guest Network - AP Mode - Isolation?

< Deco

Guest Network - AP Mode - Isolation?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Guest Network - AP Mode - Isolation?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

mikeinet

2022-04-08 01:30:11

Posts: 3

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2022-04-08

Guest Network - AP Mode - Isolation?

2022-04-08 01:30:11

Model: Deco M9 Plus

Hardware Version:

Firmware Version:

I have my Deco9 setup in AP mode with a firewall behind it doing DHCP and such.

I have both guest and "regular" network being served DHCP - one IP range.

There seems to be some undocumented AP Isolation mode setup... I can't seem to have items on my guest network be communicating with my regular network when it's in AP mode.

Is this something I can configure?

5 Reply

David-TP

2022-04-13 06:15:38

Posts: 12443

Helpful: 1719

Solutions: 1199

Stories: 9

Registered: 2020-04-14

Re:Guest Network - AP Mode - Isolation?

2022-04-13 06:15:38

@mikeinet

Thank you very much for the feedback and sorry for the delay.

Just to be clear, the issue you have is that, when Deco M9 plus is on access point mode, the guest network clients of Deco are not able to access the regular network of the firewall DHCP server, right?

Since if you are talking about the main network of Deco itself, there is an option "isolated from main network" on Deco APP>More>WiFi and if you do not wish them to be isolated, you could leave it disabled.

Best regards.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! Deco BE85_1.1.1 Supports WireGuard VPN,Channel Selection and Matter Deco BE65_V2_1.1.0 Supports WireGuard VPN, Channel Selection and More ▶Deco APP 3.8.102/3.8.112-Ready for A New Deco Onboarding Experience! Try to leave a Message if urgent help is required.

mikeinet

LV1

2022-04-13 12:14:50

Posts: 3

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2022-04-08

Re:Guest Network - AP Mode - Isolation?

2022-04-13 12:14:50

@David-TP - thanks for your reply

everyone gets dhcp without issue

the issue is that guest network users are isolated from main network

I see no option to disable this where you noted to look in the app

David-TP

2022-04-14 06:43:11

Posts: 12443

Helpful: 1719

Solutions: 1199

Stories: 9

Registered: 2020-04-14

Re:Guest Network - AP Mode - Isolation?

2022-04-14 06:43:11

@mikeinet

Hi, can I have a picture of the guest network settings on your APP, such as

By the way, I see there is a Deco M3W under your tp-link ID and is it still online and connected to the mesh since the firmware of Deco M3W does not support this feature yet.

2b07ce2595684f0ab1913ae85876418a

mikeinet

LV1

2022-04-14 12:22:25

Posts: 3

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2022-04-08

Re:Guest Network - AP Mode - Isolation?

2022-04-14 12:22:25

ahh So it doesn't support this yet. When will

this be availiable? @David-TP

how is the isolation being done? Vlan? What is the config for this? Perhaps I could handle something with my firewall

David-TP

2022-04-15 06:28:40

Posts: 12443

Helpful: 1719

Solutions: 1199

Stories: 9

Registered: 2020-04-14

Re:Guest Network - AP Mode - Isolation?

2022-04-15 06:28:40

@mikeinet

Hi, I am sorry that I did not know the ETA either.

And if you do not wish the guest network and main network of Deco are separated under access point mode, you could unplug Deco M3W first, left Deco M9 plus only, then you will see this option on the Deco APP, and you could turn it off.

Guest Network - AP Mode - Isolation?

Guest Network - AP Mode - Isolation?

Information

Voters 0

Tags