New Release Deco M5 1.6.1
Latest Firmware Release:
For Deco M5(V1/V2/V3/V3.2)
Improvements:
1. Optimized the Monthly Reports.
2. Improved system reliability.
Bug fixed:
1. Fixed the bug that clients won't be able to obtain IP addresses randomly.
2. Fixed the bug that insight/time limit of parental control won't reset the next day.
3. Fixed the bug that No-IP DDNS doesn't take effect under PPPoE connection.
4. Fixed the bug that the client list randomly does not show any client or recognizes satellite Deco as a client.
---------------------------------------------------------------------------------------------------
History Release
For Deco M5(V1/V2/V3/V3.2)
New Features/Enhancement:
1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
2. Added support for customizing Satellite Deco signal source under Deco App > Internet > Select the Satellite Deco > Signal Source.
3. Added support for customizing clients connection preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
4. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS
5. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP
6. Added a prompt when the Ethernet link rate goes down to 100Mbps.
7. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
8. When configuring Deco for the first time, you can choose to establish an IPv6 connection directly.
Notes:
1. Please update your Deco APP to the latest version for the new features.
2. If there are other Deco models in the Mesh network, you may miss some new features but this feature will be supported via firmware update in the future.
3. You may miss some new features when Deco is set to Access Point mode.
Related Articles:
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi, yes and I happen to see you have updated to firmware 1.6.0 already
, and is everything going on all right?
Thank you very much.
- Copy Link
- Report Inappropriate Content
@TP-Link WiFi routers have been in the news recently for security vulnerabilities: https://www.iot-inspector.com/blog/router-security-check-2021/ . Of the 11 routers tested, TP-Link Archer AX6000 had the most vulnerabilities at 32. Does the new Deco firmware fix the vulnerabilities it has in common with the AX6000?
- Copy Link
- Report Inappropriate Content
Hi, welcome to the community.
Thank you very much for your feedback.
As for the vulnerabilities reported by IoT Inspector, except for Archer AX6000, currently, we have not received any similar feedback on other models.
And our senior engineers are investigating and will keep updating this advisory as more information becomes available. Once an affected model is confirmed, the new firmware to fix this issue will be released very soon.
If you have any further concerns, please feel free to submit a security-related inquiry regarding one of our products to TP-Link Technical Support.
Thank you again.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@TP-Link The monthly report cannot be access in 1.6.0 version, It just load and the Deco App Hangs.
- Copy Link
- Report Inappropriate Content
Hi, thank you for the feedback.
Please go to Deco APP>three lines on the top left>help>contact us>suggestions and add the APP log, then send the APP log to us.
Thank you again.
- Copy Link
- Report Inappropriate Content
New Features/Enhancement:1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
Note: This feature is ONLY supported when the Deco with the firmware 1.6.0 installed is set as the Main Deco.
So does this mean i can schedule a reboot to all deco's connected to the main deco?
5. Added Smart DHCP on/off switch under Access Point mode.Note: This feature is ONLY supported when the Deco with the firmware 1.6.0 installed is set as the Main Deco.
Smart DHCP is enabled by default. When the Smart DHCP function is enabled, Deco will periodically check whether the DHCP Server in the LAN is working properly, and when it stops working, Deco will take the initiative to assign IP addresses to the devices in the LAN.
Hmmm.. This is a good feature but shouldn't you guys allow Router Mode to be configured so that DHCP can be Enabled/Disabled? This should be more of the priority isn't it? almost all router allows such feature anyway.
- Copy Link
- Report Inappropriate Content
So does this mean i can schedule a reboot to all deco's connected to the main deco?
Yes, you are right.
Hmmm.. This is a good feature but shouldn't you guys allow Router Mode to be configured so that DHCP can be Enabled/Disabled? This should be more of the priority isn't it? almost all router allows such feature anyway.
For the DHCP on/off under wireless router, many standard routers have this feature but when would you use this feature, or for what purpose? Currently, we haven't seen such a necessity to disable DHCP under wireless router mode. Some users do not want Deco to work as a DHCP server and still want its parental control /QoS feature, but it is not what Deco Mesh is mainly designed for. Please feel free to send us a feedback via Deco APP>Help>Contact Us>Suggesions and tell us more why you need this feature.
Update:
The second edition of 1.6.0 firmware(Deco M5 1.6.0 build 20220214) has been updated no the original post and It has improved all the reported issues on the first beta version.
Any feedback would be highly appreciated.
PS: if you want to know the release roadmap of firmware 1.6.0 on other models or the ETA of official 1.6.0 on Deco M5, please comment on this link.
When will 1.6.0 be released for the Deco
Thank you very much.
Best regards.
- Copy Link
- Report Inappropriate Content
@TP-Link I installed the new firmware update today and my internet speeds are now about 1/6 of what they were previously. I've tried rebooting the Deco. I have 3 S4R.
- Copy Link
- Report Inappropriate Content
Hi, Thank you for the feedback
Since the original post is about M5 with 1.6.0, and you have S4, I believe the firmware you have updated is 1.5.1?
Can I have more details about your current speed issue, such as:
1. is Deco S4 working as an access point, or wireless router?
2.Did you test the Ethernet connection as well as the 5ghz from the main S4----it is suggested that you could turn off the 2.4ghz band on the Deco APP to have a test.
Thank you and wait for your reply.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 12350
Replies: 53
Voters 1
