Home Network Community > Deco > How to change the layout of the Decos
< Deco

How to change the layout of the Decos

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

How to change the layout of the Decos

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
How to change the layout of the Decos
How to change the layout of the Decos
2020-11-30 16:29:12
Model: Deco X20  
Hardware Version: V6
Firmware Version: 1.2.6 build 20201013

Hello,

 

When setting my New X20 Deco router,  I accidentally select the defaul layout.  I have 3 deco unit, one is the base in the basement, 2nd in the main floor, and 3rd in the 2nd floor.

 

I want to change the layout to the current positions of my decos, how I do it?

 

Will changing the layout will help improving the signal?  right now the 2nd floor get weeker signal and speed compare to the main floor and the basement.

 

Note:  the default layout is one floor, while my current setup is like 3 floor (basement, 1st and 2nd floor)

 

Thanks

Phi

 

 

 

 

  1      
 
  1      
 
#1
Options
3 Reply
Re:How to change the layout of the Decos
2020-12-01 23:04:29

@Alpharetta 

 

The Layout is just for placement assistance and does not affect how the decos perform.  You can from the mainscreen tap on the globe and then each indvidual deco and give them a location. But that is just for tracking incase a unit goes down you know which one. 

Check out the Latest: Recent Smart Home Features and Updates for Tapo and Kasa Securing Your TP-Link ID with 2FA:Deco and Tether | Smart Home Splash into a Smarter Summer with Sub-G Sensors, Matter, and Apple Home!
  0  
  0  
#2
Options
Re:How to change the layout of the Decos
2020-12-02 01:14:59

@Carl Thanks so much for your answer.  It seems using the wired Ethernet cable back haul to connect to the deco units is the best practices.  But if we don't go that route,

the base unit should be the center, and the other units surround it, correct?

 

Current my layout is like 

1. Basement: modem - Base Deco Unit as the router

2. Main floor - 2nd deco unit

3. 2nd floor - 3rd unit

 

I notice that the wifi speed in the basement if pretty fast 500 MB, on the main floor it's 300 MB, and on the 2nd floor it reduces down to 200 MB

 

So should I rewire my system so that:

 

1.  Basement - remote deco unit

2.  Main floor - Modem and base deco unit

3.  2nd floor - another remote deco unit

 

Will this help to improve the speed through out the house?

 

Best

Phi

 

  0  
  0  
#3
Options
Re:How to change the layout of the Decos
2020-12-02 19:08:45

@Alpharetta 

 

Yes that is the best recommend deployment.  With no more than 25-30 feet between units and units at least 10-15 feet from a exteior wall.  This way you are getting the most out of each units wireless signal. There will always be a small drop in speed as you move from the source and the furhter from a node you are.  though with the main unit set in the middle of the home overall lost will be reduced. 

Check out the Latest: Recent Smart Home Features and Updates for Tapo and Kasa Securing Your TP-Link ID with 2FA:Deco and Tether | Smart Home Splash into a Smarter Summer with Sub-G Sensors, Matter, and Apple Home!
  0  
  0  
#4
Options

Information

Helpful: 1

Views: 5297

Replies: 3

Related Articles
 problem add some decos to my network
664 0
 expanding decos - dropping nodes
45 1
multiple decos
637 0
How to swap Decos
653 0
About how to connect between Decos
566 0
Add whitelisting to Decos
11235 23
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.