I can't disable the WMM in QoS after I upgrade to 5.3.1...

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

I can't disable the WMM in QoS after I upgrade to 5.3.1...

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
I can't disable the WMM in QoS after I upgrade to 5.3.1...
I can't disable the WMM in QoS after I upgrade to 5.3.1...
2022-05-17 07:44:15
Model: EAP225  
Hardware Version: V3
Firmware Version: 5.0.7 Build 20211026 Rel. 33125

Hy Support Team!

 

Why deleted the wmm turn on/off button on EAP config??? I use 2 system in a big hotel:

- software controller with 5.3.1 <- :(   for workers

- OC300 hw controller. This is the biggest system with 30xEAP 225 and a lot of old walls... I needed to turned of the wmm because the tx signals was too high.

 

So if the oc 300 will get it, then I cannot use the the omada system because the developers thinks it unnessesary?

 

Regards, Daniel.

  0      
  0      
#1
Options
6 Reply
Re:I can't disable the WMM in QoS after I upgrade to 5.3.1...
2022-05-17 12:55:41

It was in the changelog I think.  WMM is required for 802.11n/ac

  0  
  0  
#2
Options
Re:I can't disable the WMM in QoS after I upgrade to 5.3.1...
2022-05-17 12:58:40

  @mackworth Yes, it was in that. But the question: why?

  0  
  0  
#3
Options
Re:I can't disable the WMM in QoS after I upgrade to 5.3.1...
2022-05-17 12:59:45

  @mackworth and why can't connect 802.11n/ac without wmm?

  0  
  0  
#4
Options
Re:I can't disable the WMM in QoS after I upgrade to 5.3.1...
2022-05-17 13:00:20

  @Daniel-nio Because its pretty fundamental for 802.11n and above.  Turning it off is probably not the solution to the problem you are having.

  0  
  0  
#5
Options
Re:I can't disable the WMM in QoS after I upgrade to 5.3.1...
2022-05-18 08:18:33 - last edited 2022-05-18 08:18:53

  @Daniel-nio You can only do Rate Limit on Omada Controller and if you limit the EAP speed to 54Mbps, then it will work on 802.11 b and no WMM enable. 

 

However like mackworth said, WMM may be not related to your original issue. Can you share more details about why you want to disable WMM?

  0  
  0  
#6
Options
Re:I can't disable the WMM in QoS after I upgrade to 5.3.1...
2022-05-18 12:09:03

  @Somnus Hy Somnus!

 

Our own wifi system have 30 EAP on 4 floors. The clients has a smart tv, internet radio etc.. so the three wifi channels with 20 Mhz are 70-80% utilization before I turned off the wmm. After that it is 30-40%. Plus I enabled the Minimum, Data Rate Control/ Disable CCK Rates + Send Beacons at 1 Mbps. The clients told me before that(and I also saw), connection lost problems in the oldest and newest devices too, after that it is work fine.

  1  
  1  
#7
Options