Home

Forums

Stories

Knowledge Base

Business Community > Routers > Access Modem UI connected to ER605

< Routers

Access Modem UI connected to ER605

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Access Modem UI connected to ER605

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

youbarajsha

2023-09-20 13:52:57

Posts: 10

Helpful: 0

Solutions: 1

Stories: 0

Registered: 2023-09-04

Access Modem UI connected to ER605

2023-09-20 13:52:57

Tags: #WAN Setup #Routing

Model: ER605 (TL-R605)

Hardware Version: V2

Firmware Version: 2.1.2

I have my ISP provided modem (ISP router in bridge mode) connected to ER605 in an Omada controller enviroment. How can i access the Modem web UI from LAN? The Modem is on subnet 192.168.1.0/25 and ER605 on 172.27.27.0/24.

4 Reply

d0ugmac1

LV5

2023-09-20 16:04:42

Posts: 2149

Helpful: 791

Solutions: 194

Stories: 0

Registered: 2022-03-05

Re:Access Modem UI connected to ER605

2023-09-20 16:04:42

@youbarajsha

What's the management IP of the modem when in bridged mode? You just need to create a static route for that IP/subnet via the WAN port.

<< Paying it forward, one juicy problem at a time... >>

youbarajsha

LV1

2023-09-22 05:53:16 - last edited 2023-09-22 13:03:29

Posts: 10

Helpful: 0

Solutions: 1

Stories: 0

Registered: 2023-09-04

Re:Access Modem UI connected to ER605

2023-09-22 05:53:16 - last edited 2023-09-22 13:03:29

@d0ugmac1 Thanks for the info. Can you help me a little more here. My bridge mode ip to access the modem is 192.168.1.1 and my LAN is on 172.27.27.1. I know there is an option Transmission -->Routing-->Static Route in Omada controller and ER605, but I am not sure how to set it up exactly. Much thanks.

So far I have done the follwing but still not able to access the modem at 192.168.1.1

Transmission --> Routing --> Static Routing

Name - ISP Modem

Status - Enabled

Destination IP/Subnet: 192.168.1.1/32

Route Type: Interface

Interface: WAN

d0ugmac1

LV5

2023-09-23 02:54:58

Posts: 2149

Helpful: 791

Solutions: 194

Stories: 0

Registered: 2022-03-05

Re:Access Modem UI connected to ER605

2023-09-23 02:54:58

@youbarajsha

Here what I used back when I had Starlink at one of my sites. Just change the 192.168.100.1/24 subnet to 192.168.1.1/24 and you should be good.

<< Paying it forward, one juicy problem at a time... >>

KJK

LV4

2023-09-23 20:12:11 - last edited 2023-09-23 20:16:35

Posts: 317

Helpful: 118

Solutions: 31

Stories: 0

Registered: 2022-03-29

Re:Access Modem UI connected to ER605

2023-09-23 20:12:11 - last edited 2023-09-23 20:16:35

@youbarajsha

So far I was able to avoid those modem/router combos so I’m not sure about your issue. Also, it looks like the bridge mode can mean different things depending on the combo. However it looks like you are trying to access the LAN side of the combo, not the modem. In that case, I think you just can’t do it from behind the ER605. I don’t think there is a gateway you can use for it. You would need to connect your PC/laptop directly to the ISP router and have it in the same subnet as the router.

Kris K

Access Modem UI connected to ER605

Access Modem UI connected to ER605

Information

Voters 0

Tags