What ip should I use?
I am switching over to the Omada system for my network because I love the way it works. I love the user interface, and from what I have seen, the reliability.
I will have multiple EAPs, 4 different Omada Poe+ switches, OC200, and ER605 router.
Anyway, I know that the Omada router and hardware controller, along with all other devices like the 192.168.0.1 etc. address, and it is the default. I know I can use anything with it, but is it better to use the .0 because it is default?
Why I'm asking is that I have many cameras, and devices that are static to a 192.168.1. address, and I would have to change them all. Just some words of wisdom from the wise would be welcome.
Thanks.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@d0ugmac1 it is wired. I won't pick it up. No mesh.
- Copy Link
- Report Inappropriate Content
Verify the AP is powered, green led on right hand side. Factory reset it, button is beside the ethernet port.
- Copy Link
- Report Inappropriate Content
@d0ugmac1 it is green for sure. Just like all the other ones. What is the procedure for a reset? I have stuck a clip in for 10 seconds. There was blinking etc.
Also, as I am waiting for the EAP to maybe be found, I have been going in and setting static ip addresses for some of my things. I can't seem to get to the static ip of the switches. I really want to set my switches with a static ip, but I don't find the option.
- Copy Link
- Report Inappropriate Content
@ingeborgdot if you hold the reset for more than 5 seconds it will blink I think orange/green and that tells you its set to factory mode. The controller should then see it and place it in pending mode. From there you can adopt. Once adopted you can modify to make it static from dhcp and whatever changes you need to make. I had to do that yesterday. I moved all my private stuff to its own VLAN and left all the Omada on the native VLAN or management VLAN. But something got confused and I just easily did a factory reset/adopt to get it working again.
If you go to devices and select the switch then when the side bar opens, you can go to config and inside there you will see the tab for ip addresses and you can take it off dhcp and make it static
- Copy Link
- Report Inappropriate Content
@Fleegle61 There is no tab for ip addresses under config in devices. There is for clients, but not devices. There is General, VLAN interface, Static Route, Services, Manage Device.
As for the EAP, I have put in the clip held it till it did all the blinking. I've held it for 5 seconds and tried, 10 seconds and tried, 15 seconds and tried, 20 seconds and tried.
When I put it on the system, nothing recognizes it.
- Copy Link
- Report Inappropriate Content
@Fleegle61 I found it. It is under VLAN interface, edit interface, IP Address Mode:
- Copy Link
- Report Inappropriate Content
I still can't get the EAP225 to be discovered. I'll keep trying. Maybe a Return to sender.
- Copy Link
- Report Inappropriate Content
@ingeborgdot that seems odd. If you do a factory reset and the AP is connected to the same subnet as the controller it should work, unless you moved the controller to another VLAN other than 1???
As I noted, I factory reset mine yesterday since the controller was stuck adopting. After I did that and the controller timed out on the adopting, then it came up pending and from there once I started the adoption it just went to provisioning, configuring and then connected.
Also check the POE port you are using to make sure that you have the "ALL" profiled checked just in case. Maybe the controller canf see the AP if its not set to ALL.....
- Copy Link
- Report Inappropriate Content
@Fleegle61 I only have 1 Vlan at this time. The Poe is set to all. The port shows it has Poe but it says link down. No matter where I put it, it says link down. I have tried 2 different Poe switches all with the same result.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 2665
Replies: 42
Voters 0
No one has voted for it yet.