Business Community > WiFi > OC200 + EAP245 V3 - wireless speed optimization?
< WiFi

OC200 + EAP245 V3 - wireless speed optimization?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

OC200 + EAP245 V3 - wireless speed optimization?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
OC200 + EAP245 V3 - wireless speed optimization?
OC200 + EAP245 V3 - wireless speed optimization?
2020-04-08 01:55:41 - last edited 2020-04-08 01:56:55
Model: EAP245  
Hardware Version: V3
Firmware Version: 2.4.0 Build 20200117 Rel. 39932

Hi, installed today an OC200 controller plus two EAP245 V3 access points, at home.

 

Both AP are connected to the router with an ethernet cable.

 

Latest firmware on everything:

 

OC200 runs Firmware Version:

1.2.1 Build 20191126 Rel.59455

 

Controller Version:

3.2.5

 

Each EAP245 V3 runs Firmware Version:

2.4.0 Build 20200117 Rel. 39932

 

Now an interesting (maybe not so much?) part: I replaced two older Archer C2600 wireless routers, working strictly as two independent AP.

 

So on these C2600 routers (AP) I was getting up to 540 Megabit down on both my iPhone and iPad.

 

On the new EAP245 V3 though I can't get anything above 400-410 Megabit down.

 

The wired speed in the house is approx 940 down.

 

Anything in the settings I can change/optimize?

For example, this online review is claiming 855 Megabit down, I can't seem to get anywhere near that speed.

h_t_t_p_s://dongknows.com/tp-link-eap245-v3-omada-poe-access-point-review/

 

Thanks!

  0      
 
  0      
 
#1
Options
7 Reply
Re:OC200 + EAP245 V3 - wireless speed optimization?
2020-04-08 12:36:27

Hi @NorthGraves,

 

I have a very similar setup (Fios Gigabit, OC200, 2x EAP225V3).  I use separate SSID's for 2.4GHz and 5.8GHz -- no band steering, no airtime fairness.  I have about 40 devices on my wireless network, many apple products, several Lenovo laptops, and various Nest cams, etc.

 

Unlike Ethernet, where these days you usually get at least 80-95% of the "rated speed" (e.g. ~900 Mbit over  1 Gigabit), with Wifi there are a number of other factors.  Without going into too many technical details, due to overhead, retransmission, payload vs header sizes, etc. real application throughput (e.g. 400-500Mbit/s using a speed test over a 5.8GHz, 80MHz, 2x2 connection) is generally, at best 40-60% of the air link speed.

 

So, given your Apple device (like mine) which has a 2x2 MIMO 802.11ac radio, it's air link speed will be at most 866 Mbit/s -- given a very strong signal (both from the AP and from your handset back).  Even though the EAP245 supports 3x3, since your client does not, it can't use it.  So, you can expect to get at most 40-60% of 866 as real, usable throughput.

 

Now that said, I have notices that I peak out around ~400-450 Mbit/sec, very rarely hitting ~500Mbit/s on my EAP225's when sitting in the same room with them (one iso in my beadroom and one is downstairs in my office).  This seems to depend a lot on what speed test I use (SpeedSmart (my favorite), Speedtest (ookla), or Fast (Netlix).  For iOS I also like "Wi-Fi SweetSpots" which is not a speed test, but rather displays the air link speed (aka 866) so you can see how it changes as you move away from the AP.

 

But, you are right.  I have seen subtle differences between different AP devices/chipsets.  My Verizon FIOS Routers (which also has an AP that I normally disable) is capable of slightly faster 802.11ac 80MHz 2x2 speeds.  Using the DFS channel (which it annoys that TP-Link does not support) I can often get 500-550Mbit/sec on speed tests when I am in the same room with it -- of course this is with one single client on its SSID (my iPhone XSM iOS 13.4 and now 13.4.1) on wide open spectrum (DFS), connected to my FIOS with little or no switching latency/overhead.

 

For me, I prefer the management capabilities of the TP-Link solution, it's resiliency under multiple heavy users, and the ability of my one EAP225 (in my bedroom over MOCA) to failback to Wifi MESH once or twice a year when my MOCA network flakes out (usually when the FIOS router restarts).

 

So, sorry I couldn't be more help.  I, too, wish my EAP's where a littel speeder.  But they seem to make up this minor shortfall with capacity and reliability.

 

I don't have any 3x3 clients to test with.  I have an older EAP245V1 that I've retired.  I've thought about "upgrading" to the newer EAP245V3's for the hope of better MU-MIMO given 3x3 and the number of clients I have.  But the 245's do not currently support MESH (need Beta firmware), and to really get much benefit from MU-MIMO you really need at least 4x4 MIMO on the AP per radio.

 

But there are a number of advanced users on this board (and TP-Link reps) so hopefully they will chime in with some suggestions/comments.

 

  0  
  0  
#2
Options
Re:OC200 + EAP245 V3 - wireless speed optimization?
2020-04-08 12:56:50

@JSchnee21 

 

Thanks!

 

By the way, this is what I got before trying to play with settings:

 

https://www.speedtest.net/result/i/3808241225

 

So currently I use both 5 and 2.4 on the same (main) SSID, band steering, seamless routing, and mesh (even if it is not supported by the AP yet).

 

The "funny" part is I tried disabling both 2.4 and 5 on the second AP, and disabling 2.4 on the first one, saved,

leaving only 5 GHz on one AP and standing in front of it...didn't change the results at all.

 

Tried playing with 802.11ac only - same - no difference.

 

Tried playing with 20/40/80 Hz settings - same - no difference.

 

So I guess I'll keep it as is for now, as you can see I can get peak 424, and I am getting stable 300 down pretty much all over the house, which is not bad.

  0  
  0  
#3
Options
Re:OC200 + EAP245 V3 - wireless speed optimization?
2020-04-08 13:19:13
Sure. This has been a focus of mine as well. I did notice a small speed increase after upgrading from iOS 13.4 to 13.4.1. Using SpeedSmart, if I stand under my Ethernet connected AP I do sometimes get as high as ~500-550Mbit/sec. But often not. Throughout my house I generally only see ~100-300Mbit/sec per client, but that's more than adequate for my needs. Interestingly, I tend to get somewhat better upload speeds on these AP's than I do download speeds. Not sure why that is. When I've had airtime fairness on in the past, I've had issues with some of my clients (Nest) staying connected -- but I haven't tried this again recently. Yes, I assume the 20/40/80 setting will "auto select" the bandwidth depending on the amount of RF interference so it could potentially select less than 80MHz on occasion (versus selecting 80 only). But until WiFi 6 and higher degrees of MIMO (e.g. 3x3 and above) become more prevalent in both AP's and Clients OR 160 MHz bandwidth (CA w/DFS) or in the new 6E greenfield, I don't see usable Wifi bandwidth per client exceeding ~400-500 Mbit/sec anytime soon. I also find that my AP's tend to auto select the same channel if I let them. So I usually set them manually (3 & 9 for 2.4GHz (1,6, and 11 are crowded), and 36 & 149 for 5.8GHz). I'd love to add a 3rd AP, but without use of the DFS spectrum I don't have any "room" per se.
  0  
  0  
#4
Options
Re:OC200 + EAP245 V3 - wireless speed optimization?
2020-04-09 10:38:06 - last edited 2020-08-12 06:40:43

NorthGraves, unfortunately I have no EAP245 at hand currently, but I can show you some values measured with EAP225 V3.

 

First of all, what you are measuring with web-based »speed« tests is the throughputs of the Internet uplink, of the web server the test is being run on and of your client system over your wireless LAN. You are not measuring WiFi throughput of an EAP alone.

 

For example, with EAP225 in 802.11ac-only mode and 80 MHz channel width in the 5 GHz band, I get following result on Ookla's speedtest.net:

 

 

 

That's pretty accurate; in the past I got much worser results with certain Ookla test servers assigned automatically by this speed test, e.g. something like 145 Mbps on one server and 420 Mbps on another one over a 450 Mbps uplink, both tests over Ethernet cable, not WiFi.

 

But results in today's tests over WiFi and a 1 Gbps uplink still differ by ~100 Mbps depending on the selected test server:

 

 

 

I usually prefer dslreports.com, which has been most accurate in the past, but currently tests fail due to all European test servers being off-line (except their Amsterdam soft-layer server). I don't know the reason why their European servers are off-line, maybe it's related to the lockdown.

 

So, it often connects to U.S. based servers when I'm measuring and latency is very bad (~150 to 178ms) as are results for my 1 Gbps uplink. This is one of the »better« tests with the Amsterdam server:

 

 

 

My ISP's test shows a weirdness, too:

 

 

Now, how can we reliably measure WiFi throughput of an EAP for optimization? Definitely not with web-based »speed« tests.

 

The right tool for such tasks is iperf, which is the standard tool for all kind of measurements in networks. I use WiFiPerf b/c it shows the Tx rate of the WiFi adapter for wireless tests, which is not displayed in standard iperf. You can download WiFiPerf for free in Apple's app store (AFAIK it's only available for MacOS).

 

First, we measure TCP/IP throughput to a server in the LAN. This avoids slowdowns caused by the Internet uplink and the web servers as well as the web browser used for testing (right click on image and open image in new tab to enlarge):

 

 

We get 610 Mbps to 670 Mbps throughput at a WiFi Tx rate of 867 Mbps for TCP/IP. This corresponds to a protocol overhead of 23% to 30%, which is normal in 802.11ac.

 

Note also the Noise level; I have several APs here. If I turn them off, the noise level decreases. I did set Tx power of the EAP to 23dBm to minimize interferences.

 

 

Now let's try UDP. Note that the graphical representation of WiFiPerf running on the client is of not useful for UDP, since we need to look at the server-side statistics to see the datagram loss. First, we set the send bandwidth for the test to 720 Mbps and achieve following results (note the amount of lost datagrams):

 

-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Accepted connection from 192.168.178.22, port 62130
[  5] local 192.168.178.10 port 5201 connected to 192.168.178.22 port 61837
[ ID] Interval           Transfer     Bandwidth       Jitter    Lost/Total Datagrams
[  5]   0.00-1.00   sec  84.5 MBytes   709 Mbits/sec  0.114 ms  0/10816 (0%)  
[  5]   1.00-2.00   sec  85.2 MBytes   714 Mbits/sec  0.144 ms  0/10901 (0%)  
[  5]   2.00-3.00   sec  85.2 MBytes   715 Mbits/sec  0.100 ms  0/10904 (0%)  
[  5]   3.00-4.00   sec  85.8 MBytes   719 Mbits/sec  0.113 ms  0/10976 (0%)  
[  5]   4.00-5.00   sec  86.1 MBytes   722 Mbits/sec  0.135 ms  0/11015 (0%)  
[  5]   5.00-6.00   sec  85.5 MBytes   717 Mbits/sec  0.111 ms  0/10945 (0%)  
[  5]   6.00-7.00   sec  83.6 MBytes   702 Mbits/sec  0.113 ms  220/10925 (2%)  
[  5]   7.00-8.00   sec  84.2 MBytes   706 Mbits/sec  0.134 ms  139/10918 (1.3%)  
[  5]   8.00-9.00   sec  83.8 MBytes   703 Mbits/sec  0.144 ms  351/11080 (3.2%)  
[  5]   9.00-10.00  sec  86.2 MBytes   723 Mbits/sec  0.118 ms  0/11031 (0%)  
[  5]  10.00-11.00  sec  86.1 MBytes   722 Mbits/sec  0.125 ms  0/11019 (0%)  
[  5]  11.00-12.00  sec  85.1 MBytes   714 Mbits/sec  0.113 ms  2/10893 (0.018%)  
[  5]  12.00-13.00  sec  84.8 MBytes   711 Mbits/sec  0.128 ms  138/10987 (1.3%)  
[  5]  13.00-14.00  sec  85.7 MBytes   719 Mbits/sec  0.124 ms  35/11002 (0.32%)  
[  5]  14.00-15.00  sec  86.0 MBytes   722 Mbits/sec  0.096 ms  1/11012 (0.0091%)  
[  5]  15.00-16.00  sec  85.7 MBytes   719 Mbits/sec  0.128 ms  0/10974 (0%)  
[  5]  16.00-17.00  sec  86.0 MBytes   721 Mbits/sec  0.151 ms  0/11003 (0%)  
[  5]  17.00-18.00  sec  84.6 MBytes   710 Mbits/sec  0.104 ms  102/10937 (0.93%)  
[  5]  18.00-19.00  sec  85.0 MBytes   713 Mbits/sec  0.142 ms  108/10983 (0.98%)  
[  5]  19.00-20.00  sec  84.2 MBytes   707 Mbits/sec  0.154 ms  224/11008 (2%)  
[  5]  20.00-21.00  sec  85.8 MBytes   720 Mbits/sec  0.138 ms  5/10984 (0.046%)  
[  5]  21.00-22.00  sec  84.6 MBytes   710 Mbits/sec  0.137 ms  138/10969 (1.3%)  
[  5]  22.00-23.00  sec  85.0 MBytes   713 Mbits/sec  0.113 ms  100/10977 (0.91%)  
[  5]  23.00-24.00  sec  85.2 MBytes   715 Mbits/sec  0.162 ms  119/11023 (1.1%)  
[  5]  24.00-25.00  sec  85.9 MBytes   721 Mbits/sec  0.142 ms  1/11001 (0.0091%)  
[  5]  25.00-26.00  sec  83.6 MBytes   701 Mbits/sec  0.150 ms  244/10942 (2.2%)  
[  5]  26.00-27.00  sec  85.2 MBytes   715 Mbits/sec  0.147 ms  115/11018 (1%)  
[  5]  27.00-28.00  sec  84.9 MBytes   712 Mbits/sec  0.131 ms  109/10978 (0.99%)  
[  5]  28.00-29.00  sec  85.1 MBytes   714 Mbits/sec  0.111 ms  105/10997 (0.95%)  
[  5]  29.00-30.00  sec  85.4 MBytes   716 Mbits/sec  0.131 ms  71/11001 (0.65%)  
[  5]  30.00-30.03  sec  2.84 MBytes   699 Mbits/sec  0.154 ms  0/364 (0%)  
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth       Jitter    Lost/Total Datagrams
[  5]   0.00-30.03  sec  2.51 GBytes   719 Mbits/sec  0.154 ms  2327/329583 (0.71%)  
 

Total datagram loss is 0.71%, which might be acceptable for certain applications which implement retransmissions on a higher protocol layer.

 

Next, we try 700 Mbps send bandwidth:

 

-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Accepted connection from 192.168.178.22, port 62131
[  5] local 192.168.178.10 port 5201 connected to 192.168.178.22 port 51784
[ ID] Interval           Transfer     Bandwidth       Jitter    Lost/Total Datagrams
[  5]   0.00-1.00   sec  83.1 MBytes   697 Mbits/sec  0.157 ms  0/10634 (0%)  
[  5]   1.00-2.00   sec  83.5 MBytes   700 Mbits/sec  0.137 ms  0/10682 (0%)  
[  5]   2.00-3.00   sec  83.4 MBytes   699 Mbits/sec  0.145 ms  0/10673 (0%)  
[  5]   3.00-4.00   sec  83.5 MBytes   700 Mbits/sec  0.107 ms  0/10687 (0%)  
[  5]   4.00-5.00   sec  83.5 MBytes   700 Mbits/sec  0.162 ms  0/10683 (0%)  
[  5]   5.00-6.00   sec  83.5 MBytes   700 Mbits/sec  0.131 ms  0/10682 (0%)  
[  5]   6.00-7.00   sec  83.3 MBytes   699 Mbits/sec  0.135 ms  0/10662 (0%)  
[  5]   7.00-8.00   sec  83.6 MBytes   701 Mbits/sec  0.128 ms  0/10696 (0%)  
[  5]   8.00-9.00   sec  83.5 MBytes   700 Mbits/sec  0.137 ms  0/10684 (0%)  
[  5]   9.00-10.00  sec  83.5 MBytes   700 Mbits/sec  0.160 ms  0/10683 (0%)  
[  5]  10.00-11.00  sec  83.4 MBytes   700 Mbits/sec  0.122 ms  0/10674 (0%)  
[  5]  11.00-12.00  sec  83.5 MBytes   701 Mbits/sec  0.128 ms  0/10692 (0%)  
[  5]  12.00-13.00  sec  83.4 MBytes   699 Mbits/sec  0.125 ms  0/10673 (0%)  
[  5]  13.00-14.00  sec  83.5 MBytes   701 Mbits/sec  0.117 ms  0/10692 (0%)  
[  5]  14.00-15.00  sec  83.5 MBytes   700 Mbits/sec  0.103 ms  0/10682 (0%)  
[  5]  15.00-16.00  sec  83.4 MBytes   700 Mbits/sec  0.110 ms  0/10681 (0%)  
[  5]  16.00-17.00  sec  83.5 MBytes   700 Mbits/sec  0.165 ms  0/10683 (0%)  
[  5]  17.00-18.00  sec  83.3 MBytes   699 Mbits/sec  0.152 ms  0/10666 (0%)  
[  5]  18.00-19.00  sec  83.6 MBytes   701 Mbits/sec  0.122 ms  0/10695 (0%)  
[  5]  19.00-20.00  sec  83.5 MBytes   700 Mbits/sec  0.157 ms  0/10684 (0%)  
[  5]  20.00-21.00  sec  83.4 MBytes   700 Mbits/sec  0.140 ms  0/10681 (0%)  
[  5]  21.00-22.00  sec  83.4 MBytes   700 Mbits/sec  0.131 ms  0/10678 (0%)  
[  5]  22.00-23.00  sec  83.5 MBytes   700 Mbits/sec  0.138 ms  0/10684 (0%)  
[  5]  23.00-24.00  sec  83.3 MBytes   699 Mbits/sec  0.158 ms  0/10661 (0%)  
[  5]  24.00-25.00  sec  83.6 MBytes   701 Mbits/sec  0.148 ms  0/10704 (0%)  
[  5]  25.00-26.00  sec  83.4 MBytes   700 Mbits/sec  0.130 ms  0/10681 (0%)  
[  5]  26.00-27.00  sec  83.4 MBytes   700 Mbits/sec  0.123 ms  0/10679 (0%)  
[  5]  27.00-28.00  sec  83.2 MBytes   698 Mbits/sec  0.118 ms  0/10650 (0%)  
[  5]  28.00-29.00  sec  83.7 MBytes   702 Mbits/sec  0.126 ms  0/10717 (0%)  
[  5]  29.00-30.00  sec  83.4 MBytes   700 Mbits/sec  0.127 ms  0/10680 (0%)  
[  5]  30.00-30.00  sec   208 KBytes   477 Mbits/sec  0.143 ms  0/26 (0%)  
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth       Jitter    Lost/Total Datagrams
[  5]   0.00-30.00  sec  2.44 GBytes   700 Mbits/sec  0.143 ms  0/320429 (0%)

 

That looks good. We have ~20% protocol overhead.

 

NorthGraves wrote

Tried playing with 802.11ac only - same - no difference.

 

Tried playing with 20/40/80 Hz settings - same - no difference.

 

I can't second this. Changing channel width to 40 MHz gives following results for my EAP225:

 

 

Unsurprisingly, throughput is cut by half if channel width is reduced to 40 MHz.

 

Final note: we can't measure »speed« with all those tools since speed of EM waves is always the same: it's nearly speed of light.

What we measure is throughput (WiFi rate) or goodput (data rate). Throughput/goodput depends on bandwidth, which is the theoretical max. throughput we can achieve by using a certain modulation method.

 

Conclusion: For 802.11ac @80 MHz channel width max. bandwidth is 867 Mbps. Throughput is ~700 Mbps (~19% WiFi protocol overhead) and goodput is ~640 Mbps on average (~8.5% of the WiFi bandwidth = ~7% of total bandwidth for TCP protocol overhead or in other words: ~26% protocol overhead of TCP and WiFi together).

 

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#5
Options
Re:OC200 + EAP245 V3 - wireless speed optimization?
2020-04-09 13:31:01 - last edited 2020-04-09 13:31:29

@R1D2 

 

Thank you, you've been extremely thorough, I am truly impressed.

 

Three things:

 

1) To clarify what I meant by:

 

"Tried playing with 802.11ac only - same - no difference.

Tried playing with 20/40/80 Hz settings - same - no difference."

 

Default was (and currently is):

802.11a/n/ac mixed for 5 GHz; Channel width 20/40/80 Hz

802.11b/g/n mixed for 2.4 GHz; Channel width 20/40 Hz 

Both 2.4 GHz and 5 GHz are ON on both AP

 

Here's what I meant - I was able to make things WORSE by changing some of those settings, but I wasn't able to make things BETTER by any combination of the above settings.

 

Example: Pure 802.11ac on, Channel width 80 Hz only, 2.4 GHz turned off completely, second AP turned off completely - same top ~425 Megabit speed.

 

2) I "assumed" that a gigabit wire-connected AP would easily do more than say 600-700 between itself and the router on the wire, so I (again) assumed the 425 was the WiFi bottleneck, not the wired AP to the router bottleneck. You proved that was a correct assumption.

 

3) I simply wanted to see the "net" speed from the AP to the client, after all overheards etc lost. That one seems to be ~425 in my case.

  0  
  0  
#6
Options
Re:OC200 + EAP245 V3 - wireless speed optimization?
2020-04-09 14:56:47 - last edited 2020-04-09 15:07:48

 

NorthGraves wrote

Default was (and currently is):

802.11a/n/ac mixed for 5 GHz; Channel width 20/40/80 Hz

802.11b/g/n mixed for 2.4 GHz; Channel width 20/40 Hz 

Both 2.4 GHz and 5 GHz are ON on both AP

 

The issue with mixed modes is the SSID beacon: in 802.11b legacy mode the EAP has to send a beacon every then and when with 1 Mbps WiFi rate. To make best use of AirTime available to all APs and clients I always use:

  • 802.11n-only mode for the 2.4 GHz band at 20 MHz channel width in overcrowded areas, 40 MHz channel width in rural areas.
  • 802.11n/ac-only mode for the 5 GHz band at 20/40/80 MHz channel width for public hotspots, but 80 MHz-only for offices etc.

 

Lowering Tx power can be useful to minimize interferences if you have many EAPs using the same channel and if the distance between those EAPs is < 15m. In all other cases I would set it to »High«.

 

Also make sure to mount the EAP at an ideal position: this is the center of the area you want to cover. Inside the 60º angle you should get an excellent signal and best possible throughput. Inside the 74º angle the signal is acceptable, but throughput drops somewhat. Outside this angle throughput drops even more:

 

 

2) I "assumed" that a gigabit wire-connected AP would easily do more than say 600-700 between itself and the router on the wire, so I (again) assumed the 425 was the WiFi bottleneck, not the wired AP to the router bottleneck. You proved that was a correct assumption.

 

Yes. The EAP245 should exceed the values I measured for EAP225, but your wireless client must support it, too.

 

3) I simply wanted to see the "net" speed from the AP to the client, after all overheards etc lost. That one seems to be ~425 in my case.

 

iperf resp. WiFiPerf is well suited for that. You would need a wired server or PC running an iperf instance as the server and using a laptop or PC connected wirelessly to the EAP to run the iperf/WiFiPerf client. See https://iperf.fr/ for more information about this measuring tool.

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#7
Options
Re:OC200 + EAP245 V3 - wireless speed optimization?
2020-04-09 15:02:11 - last edited 2020-04-09 15:02:32

@R1D2 

 

Thanks again, I will try to kill b/g (2.4) + a (5), see if nobody feels a thing:-).

  0  
  0  
#8
Options

Information

Helpful: 0

Views: 5720

Replies: 7

Related Articles
EAP245 V3 not showing stats with OC200 controller version 3.2.14
1070 0
EAP245 V3 from Amazon
818 0
EAP245(V1) with OC200(V2)
686 0
EAP245 V3 Speed Issue
2242 0
EAP245 V3 TCPDUMP inquiry
828 0
EAP245 v3 :: 5GHz channels
2307 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.