Business Community > Pharos Wireless Bridges > eap110 shows TX-Power 20 in settings but is only 14 in iwconfig
< Pharos Wireless Bridges

eap110 shows TX-Power 20 in settings but is only 14 in iwconfig

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

eap110 shows TX-Power 20 in settings but is only 14 in iwconfig

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
eap110 shows TX-Power 20 in settings but is only 14 in iwconfig
eap110 shows TX-Power 20 in settings but is only 14 in iwconfig
2018-04-01 23:11:47
Model :

Hardware Version :

Firmware Version :

ISP :

Hi,

Just a bit frustrated about the WLAN strength of the EAP110 newest Firmaware (EU).
I realized that each country with English language does get the same (EU) firmware even US (when TRUMP will notice that:-)

I putty to the device and iwconfig shows me (below) only 14dBm instead of 20 as set in GUI

ath0 IEEE 802.11ng ESSID:"Out"
Mode:Master Frequency:2.447 GHz Access Point: 70:4F:57:44:F2:B6
Bit Rate:144.4 Mb/s Tx-Power=14 dBm
RTS thr:off Fragment thr:off
Power Management:off
Link Quality=94/94 Signal level=-96 dBm Noise level=-95 dBm
Rx invalid nwid:116 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

This isn´t OK I think.
So how to change that to the at least minumum allowed 20 dBm (20dBm * Omni antennas %dBm = 100 dBm)?
  0      
 
  0      
 
#1
Options
10 Reply
Re:eap110 shows TX-Power 20 in settings but is only 14 in iwconfig
2018-04-02 22:44:36

boris03 wrote


I realized that each country with English language does get the same (EU) firmware even US (when TRUMP will notice that:-)


What makes you think so? EU version is EAP110v2_eu_1.2.0_[20170915-rel35854], while US version is EAP110v2_us_1.2.0_[20170915-rel35864].


I putty to the device and iwconfig shows me (below) only 14dBm instead of 20 as set in GUI


iwconfig shows you TX power, not EIRP. Add the antenna gain to get the EIRP. Note that most APs cap the EIRP some dB below the max. allowed 20dBm in the EU.
༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#2
Options
Re:eap110 shows TX-Power 20 in settings but is only 14 in iwconfig
2018-04-03 00:45:31
Thank you.

Sorry didn´t mention I do have the EAP110 v1. and here I can download what I want all English language firmwares are the same EU&US file!

But I could read that in earlier firmware versions you could increase to 27 dBm instead 20 as currently maximum in settings.
Do you know how to get this increased to 27.
When searching in the internet there is no clear instruction and unfortunately there is no separate US firmware what would allow this change.
I cannot switch to US region any longer as it was possible in earlier firmare versions.
  0  
  0  
#3
Options
Re:eap110 shows TX-Power 20 in settings but is only 14 in iwconfig
2018-04-03 20:10:38

boris03 wrote

Sorry didn´t mention I do have the EAP110 v1. and here I can download what I want all English language firmwares are the same EU&US file!


Link please.

But I could read that in earlier firmware versions you could increase to 27 dBm instead 20 as currently maximum in settings.


27dBm is allowed in some foreign countries only. If you are in the EU and bought an EU device, the maximum allowed EIRP is 20dBm.

I cannot switch to US region any longer as it was possible in earlier firmare versions.


That's b/c of EU regulation frenzy. Vendors have to fulfill those requirements, else their devices are banned from the market. Note that violating those limits - e.g. by grey-importing US hardware - does pose the risk of severe penalties, including seizure of all your WiFi equipment (at least in some EU countries).
༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#4
Options
Re:eap110 shows TX-Power 20 in settings but is only 14 in iwconfig
2018-04-04 18:02:05
Hi Thanks,

But still don´t understand when highest limit should be 20 why is it 14 even when I set 20?

I bought it in Europe but no took it with me to the US, hardware isn´t different I guess this is just the firmware
and even here all English firmwares are the same as the European one - Why?

So I am still searching for a real US firmware what allows me to change not to 20 but also to 26 or 27.
  0  
  0  
#5
Options
Re:eap110 shows TX-Power 20 in settings but is only 14 in iwconfig
2018-04-05 02:12:52

boris03 wrote

But still don´t understand when highest limit should be 20 why is it 14 even when I set 20?


The setting in the web UI/Controller isn't actually TX power, it's total EIRP. Of course, this labeling is mis-leading.
I bought it in Europe but no took it with me to the US, hardware isn´t different I guess this is just the firmware
and even here all English firmwares are the same as the European one - Why?


There is a signature in the flash chip which prevents installation of US firmware on EU devices. Right, hardware is the same, but EU devices refuse to let you install US firmware.
So I am still searching for a real US firmware what allows me to change not to 20 but also to 26 or 27.


As I wrote in post #2, US firmware is different (release 35864) from the EU firmware (release 35854), at least what I see on the download pages for EU and US.
༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#6
Options
Re:eap110 shows TX-Power 20 in settings but is only 14 in iwconfig
2018-08-10 16:35:32

Hello,

is there a possibility to increase the TX power of the EAP110 or to flash a US firmware?

Thank you

  1  
  1  
#7
Options
Re:eap110 shows TX-Power 20 in settings but is only 14 in iwconfig
2020-05-21 21:13:34

any solution to this problem so we can use more tx power?

i just bought eap 110 and only allows 19dbm to be used what a shame for tplink not allow to use other country

  0  
  0  
#8
Options
Re:eap110 shows TX-Power 20 in settings but is only 14 in iwconfig
2020-05-23 10:02:31 - last edited 2020-05-23 10:02:56

@Ghk84, my EAP110-Outdoor V1 allows up to 20dBm EIRP (maximum value allowed in the EU for the 2.4 GHz band):

 

 

What EAP110-Outdoor version do you have? What country you are in? What's the maximum allowed EIRP in your country?

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#9
Options
Re:eap110 shows TX-Power 20 in settings but is only 14 in iwconfig
2020-05-23 20:15:24

@boris03 

i have the v4 indoor version, any solution to increase to an decent tx power like 22?

  0  
  0  
#10
Options
Re:eap110 shows TX-Power 20 in settings but is only 14 in iwconfig
2020-05-24 05:16:44

 

Ghk84 wrote

i have the v4 indoor version, any solution to increase to an decent tx power like 22?

 

No. It violates the law (except in the U.S.).

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#11
Options

Information

Helpful: 0

Views: 4501

Replies: 10

Related Articles
EAP 215 TX Power
356 0
 Tx power EAP650
734 0
EAP110 losing config after power loss
105 0
 EAP110 Outdoor - Power
1567 0
 EAP110-Outdoor / Tx Errors/Dropped Packets
1245 0
Wifi compatibility between 1 EAP110 and 2 CPE210
1577 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.