TL-WA5210G Access Point - Client Connection
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TL-WA5210G Access Point - Client Connection
Region : UnitedStates
Model : TL-WA5210G
Hardware Version : V2
Firmware Version : 4.4.8 Build 130502 Rel.61441n
ISP :
Hello All,
Actually I have tried too much to configure (Point to Point Bridge) Connection or (Client - Access Point) between 2 TL-WA5210G devices or two TL-WA7510N devices but I always fail although I have followed up the procedure in this link http://www.tp-link.com/en/article/?faqid=498 strictly but still having problem.
I will list my current configuration hope someone can help me.
I have two TL-WA5210G Devices.
Device 1 Connected to my internet gateway and DHCP server by wire connection and configured as an access point.
My Gateway IP is 10.1.0.254 which is acting also as a DHCP
My first TL-WA5210G which is connected to the same segment have the IP Address 10.1.0.229, Subnet Mask 255.0.0.0 and Gateway 10.1.0.254
The second segment of the network contains the second TL-WA5210G device configured as a Client with IP 10.1.0.227, Subnet 255.0.0.0 and Gateway 10.1.0.254
The second Device is connected through a switch to a PC. The PC is set to take IP Address from DHCP.
Both Devices have exactly the same security settings WPA-PSK/WPA2-PSK with the same password. My internet gateway is a Mikrotik Router which is acting also as a DHCP Server.
Although the PC can pick up the IP Address from the DHCP server which is located at the other segment which means that there is a connectivity to the other segment through the Access Points Sets but can't access my router.
I can open both Access Points configuration in the browser through IPs 10.1.0.227 and 10.1.0.229 and I can ping both from the PC without a problem but I can't ping my internet gateway 10.1.0.254 or accessing the internet from the PC.
Kindly help me solving this problem please.
Model : TL-WA5210G
Hardware Version : V2
Firmware Version : 4.4.8 Build 130502 Rel.61441n
ISP :
Hello All,
Actually I have tried too much to configure (Point to Point Bridge) Connection or (Client - Access Point) between 2 TL-WA5210G devices or two TL-WA7510N devices but I always fail although I have followed up the procedure in this link http://www.tp-link.com/en/article/?faqid=498 strictly but still having problem.
I will list my current configuration hope someone can help me.
I have two TL-WA5210G Devices.
Device 1 Connected to my internet gateway and DHCP server by wire connection and configured as an access point.
My Gateway IP is 10.1.0.254 which is acting also as a DHCP
My first TL-WA5210G which is connected to the same segment have the IP Address 10.1.0.229, Subnet Mask 255.0.0.0 and Gateway 10.1.0.254
The second segment of the network contains the second TL-WA5210G device configured as a Client with IP 10.1.0.227, Subnet 255.0.0.0 and Gateway 10.1.0.254
The second Device is connected through a switch to a PC. The PC is set to take IP Address from DHCP.
Both Devices have exactly the same security settings WPA-PSK/WPA2-PSK with the same password. My internet gateway is a Mikrotik Router which is acting also as a DHCP Server.
Although the PC can pick up the IP Address from the DHCP server which is located at the other segment which means that there is a connectivity to the other segment through the Access Points Sets but can't access my router.
I can open both Access Points configuration in the browser through IPs 10.1.0.227 and 10.1.0.229 and I can ping both from the PC without a problem but I can't ping my internet gateway 10.1.0.254 or accessing the internet from the PC.
Kindly help me solving this problem please.
