Business Community > All Threads > ER7206 WAN throughput via SNMP
< All Threads

ER7206 WAN throughput via SNMP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ER7206 WAN throughput via SNMP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
ER7206 WAN throughput via SNMP
ER7206 WAN throughput via SNMP
2023-10-09 08:03:39 - last edited 2023-10-12 01:06:44
Tags: #SNMP
Model: ER7206 (TL-ER7206)  
Hardware Version: V1
Firmware Version: 1.3.0 Build 20230322

I saw few similar topics but I have to make next one, because it is still unclear to me.

Goal is to read WAN Rx and Tx throughput via SNMP. Could anybody tell me what OIDs give such parameters?

By own I found only these:

 

 

It seems I have only basic interface parameters (state, negotiated/configured speed, etc) and counters, but not throughput. Needed parameters are visible in GUI, so I believe it should be also available via SNMP. Any help will be appreciated.

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:ER7206 WAN throughput via SNMP-Solution
2023-10-10 03:16:58 - last edited 2023-10-12 01:06:44

  @JarekPrzybyl 

 

That would need to be calculated from these counters.

 

1.3.6.1.2.1.2.2.1.16.1049 [ifOutOctets.1049]
1.3.6.1.2.1.2.2.1.10.1049 [ifInOctets.1049]

 

Note that these counters are not the same as the GUI Total TX Bytes or Total RX Bytes. The SNMP counters can't be cleared.

Kris K
Recommended Solution
  4  
  4  
#2
Options
6 Reply
Re:ER7206 WAN throughput via SNMP-Solution
2023-10-10 03:16:58 - last edited 2023-10-12 01:06:44

  @JarekPrzybyl 

 

That would need to be calculated from these counters.

 

1.3.6.1.2.1.2.2.1.16.1049 [ifOutOctets.1049]
1.3.6.1.2.1.2.2.1.10.1049 [ifInOctets.1049]

 

Note that these counters are not the same as the GUI Total TX Bytes or Total RX Bytes. The SNMP counters can't be cleared.

Kris K
Recommended Solution
  4  
  4  
#2
Options
Re:ER7206 WAN throughput via SNMP
2023-10-10 20:16:20

KJK wrote

  That would need to be calculated

 

So, no way, to read just a value displayed by GUI? It will complicate my life a bit, but okay, thx!

 

 

 

  0  
  0  
#3
Options
Re:ER7206 WAN throughput via SNMP
2023-10-11 03:04:26

  @JarekPrzybyl 

 

Not to my knowledge and I actually don't expect it. It would be waisting of resources most of the time in my opinion. 

Kris K
  0  
  0  
#4
Options
Re:ER7206 WAN throughput via SNMP
2023-10-11 13:09:17 - last edited 2023-10-11 13:09:39

  @JarekPrzybyl 

 

I use Observium against my Omada network and it shows wan speed data fine.  I would suggest switching SNMP apps.  

I can not teach anyone anything - I can only make them think - Socrates
  0  
  0  
#5
Options
Re:ER7206 WAN throughput via SNMP
2023-10-11 16:37:37 - last edited 2023-10-11 17:08:48

  @KimcheeGUN 

Ok, thanks for this info, I'll check.

[edit]

I have checked. Not with your sw, but with trial of PRTG and indeed: i see rx and tx current throughput on Eth1. But still unclear for me is, if this is an exact value taken by SNMP from my router or maybe it is calculated by PRTG from counters? I'm not familiar with this software, can't find what OID is displayed.

My goal is to have OID needed value and use it in other project (Home Assistant).

 

  0  
  0  
#6
Options
Re:ER7206 WAN throughput via SNMP
2023-10-11 22:15:39

Finally I did it as @KJK adviced, measurement is working fine, thanks!

  0  
  0  
#7
Options

Information

Helpful: 0

Views: 1082

Replies: 6

Tags

SNMP
Related Articles
[ER7206]Can not connnect snmp via wan
1145 1
ER7206 & SNMP
769 3
Throughput of ER7206 v2 in dual-wan configuration ?
254 0
ER7206 SNMP Interface name to Omada/GW name mapping?
538 0
ER7206 WAN via SFP or WAN Port
732 0
TL-ER7206 SNMP
1129 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.